- 1.1-1: The shaft is supported by a smooth thrust bearing at B and a journa...
- 1.1-2: Determine the resultant internal normal and shear force in the memb...
- 1.1-3: The beam AB is fixed to the wall and has a uniform weight of 80 lb>...
- 1.1-4: The shaft is supported by a smooth thrust bearing at A and a smooth...
- 1.1-5: Determine the resultant internal loadings in the beam at cross sect...
- 1.1-6: Determine the normal force, shear force, and moment at a section th...
- 1.1-7: The cable will fail when subjected to a tension of 2 kN. Determine ...
- 1.1-8: Determine the resultant internal loadings on the cross section thro...
- 1.1-9: Determine the resultant internal loadings on the cross section thro...
- 1.1-10: The boom DF of the jib crane and the column DE have a uniform weigh...
- 1.1-11: The forearm and biceps support the 2-kg load at A . If C can be ass...
- 1.1-12: The serving tray T used on an airplane is supported on each side by...
- 1.1-13: The blade of the hacksaw is subjected to a pretension force of F = ...
- 1.1-14: The blade of the hacksaw is subjected to a pretension force of F = ...
- 1.1-15: A 150-lb bucket is suspended from a cable on the wooden frame. Dete...
- 1.1-16: A 150-lb bucket is suspended from a cable on the wooden frame. Dete...
- 1.1-17: Determine resultant internal loadings acting on section a a and sec...
- 1.1-18: The bolt shank is subjected to a tension of 80 lb. Determine the re...
- 1.1-19: Determine the resultant internal loadings acting on the cross secti...
- 1.1-20: Determine the resultant internal loadings acting on the cross secti...
- 1.1-21: The forged steel clamp exerts a force of F = 900 N on the wooden bl...
- 1.1-22: The metal stud punch is subjected to a force of 120 N on the handle...
- 1.1-23: Solve Prob. 122 for the resultant internal loadings acting on the c...
- 1.1-24: Determine the resultant internal loadings acting on the cross secti...
- 1.1-25: Determine the resultant internal loadings acting on the cross secti...
- 1.1-26: The shaft is supported at its ends by two bearings A and B and is s...
- 1.1-27: The pipe assembly is subjected to a force of 600 N at B . Determine...
- 1.1-28: The brace and drill bit is used to drill a hole at O . If the drill...
- 1.1-29: The curved rod AD of radius r has a weight per length of w . If it ...
- 1.1-30: A differential element taken from a curved bar is shown in the figu...
- 1.1-31: The supporting wheel on a scaffold is held in place on the leg usin...
- 1.1-32: The lever is held to the fixed shaft using a tapered pin AB, which ...
- 1.1-33: The bar has a cross-sectional area A and is subjected to the axial ...
- 1.1-34: The built-up shaft consists of a pipe AB and solid rod BC . The pip...
- 1.1-35: If the turnbuckle is subjected to an axial force of P = 900 lb, det...
- 1.1-36: The average normal stresses developed in section a a of the turnbuc...
- 1.1-37: The plate has a width of 0.5 m. If the stress distri bution at the ...
- 1.1-38: The two members used in the construction of an aircraft fuselage ar...
- 1.1-39: If the block is subjected to the centrally applied force of 600 kN,...
- 1.1-40: Determine the average normal stress in each of the 20-mm diameter b...
- 1.1-41: If the average normal stress in each of the 20-mm diameter bars is ...
- 1.1-42: Determine the average shear stress developed in pin A of the truss....
- 1.1-43: The 150-kg bucket is suspended from end E of the frame. Determine t...
- 1.1-44: The 150-kg bucket is suspended from end E of the frame. If the diam...
- 1.1-45: The pedestal has a triangular cross section as shown. If it is subj...
- 1.1-46: The 20-kg chandelier is suspended from the wall and ceiling using r...
- 1.1-47: The chandelier is suspended from the wall and ceiling using rods AB...
- 1.1-48: The beam is supported by a pin at A and a short link BC. If P = 15 ...
- 1.1-49: The joint is subjected to the axial member force of 6 kip. Determin...
- 1.1-50: The driver of the sports car applies his rear brakes and causes the...
- 1.1-51: During the tension test, the wooden specimen is subjected to an ave...
- 1.1-52: If the joint is subjected to an axial force of P = 9 kN, determine ...
- 1.1-53: The average shear stress in each of the 6-mm diameter bolts and alo...
- 1.1-54: When the hand is holding the 5-lb stone, the humerus H , assumed to...
- 1.1-55: The 2-Mg concrete pipe has a center of mass at point G . If it is s...
- 1.1-56: The 2-Mg concrete pipe has a center of mass at point G . If it is s...
- 1.1-57: If the concrete pedestal has a specific weight of g , determine the...
- 1.1-58: The anchor bolt was pulled out of the concrete wall and the failure...
- 1.1-59: The jib crane is pinned at A and supports a chain hoist that can tr...
- 1.1-60: If the shaft is subjected to an axial force of 5 kN, determine the ...
- 1.1-61: If the 60-mm diameter shaft is subjected to an axial force of 5 kN,...
- 1.1-62: The crimping tool is used to crimp the end of the wire E . If a for...
- 1.1-63: Solve Prob. 162 for pin B . The pin is subjected to double shear an...
- 1.1-64: A vertical force of P = 1500 N is applied to the bell crank. Determ...
- 1.1-65: Determine the maximum vertical force P that can be applied to the b...
- 1.1-66: Determine the largest load P that can be applied to the frame witho...
- 1.1-67: The pedestal in the shape of a frustum of a cone is made of concret...
- 1.1-68: The pedestal in the shape of a frustum of a cone is made of concret...
- 1.1-69: Member B is subjected to a compressive force of 800 lb. If A and B ...
- 1.1-70: The lever is attached to the shaft A using a key that has a width d...
- 1.1-71: The joint is fastened together using two bolts. Determine the requi...
- 1.1-72: The truss is used to support the loading shown Determine the requir...
- 1.1-73: The steel swivel bushing in the elevator control of an airplane is ...
- 1.1-74: Member B is subjected to a compressive force of 600 lb. If A and B ...
- 1.1-75: The hangers support the joist uniformly, so that it is assumed the ...
- 1.1-76: The hangers support the joists uniformly, so that it is assumed the...
- 1.1-77: The tension member is fastened together using two bolts, one on eac...
- 1.1-78: The 50-kg flowerpot is suspended from wires AB and BC . If the wire...
- 1.1-79: The 50-kg flowerpot is suspended from wires AB and BC which have di...
- 1.1-80: The thrust bearing consists of a circular collar A fixed to the sha...
- 1.1-81: The steel pipe is supported on the circular base plate and concrete...
- 1.1-82: The steel pipe is supported on the circular base plate and concrete...
- 1.1-83: The 60 mm * 60 mm oak post is supported on the pine block. If the a...
- 1.1-84: The frame is subjected to the load of 4 kN which acts on member ABD...
- 1.1-85: The beam is made from southern pine and is supported by base plates...
- 1.1-86: The two aluminum rods support the vertical force of P = 20 kN. Dete...
- 1.1-87: The two aluminum rods AB and AC have diameters of 10 mm and 8 mm, r...
- 1.1-88: The compound wooden beam is connected together by a bolt at B . Ass...
- 1.1-89: Determine the required minimum thickness t of member AB and edge di...
- 1.1-90: Determine the maximum allowable load P that can be safely supported...
- 1.1-91: If the allowable bearing stress for the material under the supports...
- 1.1-92: If the allowable bearing stress for the material under the supports...
- 1.1-93: The rods AB and CD are made of steel. Determine their smallest diam...
- 1.1-94: The aluminum bracket A is used to support the centrally applied loa...
- 1.1-95: 195. The pin support A and roller support B of the bridge truss are...
- 1.1-96: The pin support A and roller support B of the bridge truss are supp...
- 1.1-97: The beam AB is pin supported at A and supported by a cable BC . A s...
- 1.1-98: The long bolt passes through the 30-mm-thick plate. If the force in...
- 1.1-99: To the nearest 1 16 in., determine the required thickness of member...
- 1.1-100: The circular punch B exerts a force of 2 kN on the top of the plate...
- 1.1-101: Determine the average punching shear stress the circular shaft crea...
- 1.1-102: The bearing pad consists of a 150 mm by 150 mm block of aluminum th...
- 1.1-103: The yoke-and-rod connection is subjected to a tensile force of 5 kN...
- 1.1-104: The cable has a specific weight g (weight/volume) and cross-section...

# Solutions for Chapter 1: Mechanics of Materials 9th Edition

## Full solutions for Mechanics of Materials | 9th Edition

ISBN: 9780133254426

Solutions for Chapter 1

Get Full Solutions
Solutions for Chapter 1

18

1

This expansive textbook survival guide covers the following chapters and their solutions. Chapter 1 includes 104 full step-by-step solutions. This textbook survival guide was created for the textbook: Mechanics of Materials, edition: 9. Mechanics of Materials was written by and is associated to the ISBN: 9780133254426. Since 104 problems in chapter 1 have been answered, more than 73608 students have viewed full step-by-step solutions from this chapter.

Key Engineering and Tech Terms and definitions covered in this textbook