- 10.10.1: Knowing that the spring at A is of constant k and that the bar ABis...
- 10.10.2: Knowing that the torsional spring at B is of constant K and thatthe...
- 10.10.3: Two rigid bars AC and BC are connected by a pin at C as shown.Knowi...
- 10.10.4: Two rigid bars AC and BC are connected as shown to a spring ofconst...
- 10.10.5: The rigid bar AD is attached to two springs of constant k and is in...
- 10.10.6: The rigid rod AB is attached to a hinge at A and to two springs, 64...
- 10.10.7: The rigid rod AB is attached to a hinge at A and to two springs,eac...
- 10.10.8: A frame consists of four L-shaped members connected by fourtorsiona...
- 10.10.9: Determine the critical load of a round wooden dowel that is48 in. l...
- 10.10.10: Determine the critical load of a steel tube that is 5 m long and ha...
- 10.10.11: A compression member of 20-in. effective length consists of a solid...
- 10.10.12: Two brass rods used as compression members, each of 3-m effectivele...
- 10.10.13: A column of effective length L can be made by gluing togetheridenti...
- 10.10.14: Determine the radius of the round strut so that the round andsquare...
- 10.10.15: A compression member of 7-m effective length is made by weldingtoge...
- 10.10.16: A column of 3-m effective length is to be made by welding togethert...
- 10.10.17: A single compression member of 27-ft effective length is obtained b...
- 10.10.18: A column of 22-ft effective length is made by welding two 9 3 0.5-i...
- 10.10.19: Member AB consists of a single C130 3 10.4 steel channel oflength 2...
- 10.10.20: Knowing that P 5 5.2 kN, determine the factor of safety for thestru...
- 10.10.21: A rigid block of mass m can be supported in each of the four wayssh...
- 10.10.22: Each of the five struts shown consists of a solid steel rod. (a) Kn...
- 10.10.23: A 1-in.-square aluminum strut is maintained in the position shownby...
- 10.10.24: A 1-in.-square aluminum strut is maintained in the position shownby...
- 10.10.25: Column AB carries a centric load P of magnitude 15 kips. Cables BCa...
- 10.10.26: A W8 3 21 rolled-steel shape is used with the support and cablearra...
- 10.10.27: Column ABC has a uniform rectangular cross section with b 512 mm an...
- 10.10.28: Column ABC has a uniform rectangular cross section and is bracedin ...
- 10.10.29: An axial load P is applied to the 32-mm-diameter steel rod AB assho...
- 10.10.30: An axial load P 5 15 kN is applied at point D that is 4 mm fromthe ...
- 10.10.31: The line of action of the 75-kip axial load is parallel to the geom...
- 10.10.32: An axial load P is applied to the 32-mm-square aluminum bar BCas sh...
- 10.10.33: An axial load P is applied to the 1.375-in. diameter steel rod ABas...
- 10.10.34: The axial load P is applied at a point located on the x axis at adi...
- 10.10.35: An axial load P is applied at point D that is 0.25 in. from the geo...
- 10.10.36: An axial load P is applied at a point located on the x axis at a di...
- 10.10.37: Solve Prob. 10.36, assuming that L is 4.5 m.
- 10.10.38: The line of action of an axial load P is parallel to the geometrica...
- 10.10.39: A brass pipe having the cross section shown has an axial load Pappl...
- 10.10.40: Solve Prob. 10.39, assuming that the axial load P is applied 10 mmf...
- 10.10.41: The steel bar AB has a 383 38-in. square cross section and is heldb...
- 10.10.42: For the bar of Prob. 10.41, determine the required distance d forwh...
- 10.10.43: An axial load P is applied to the W10 3 30 rolled-steel column BCth...
- 10.10.44: Solve Prob. 10.43, assuming that the length of the column isreduced...
- 10.10.45: A 3.5-m-long steel tube having the cross section and properties sho...
- 10.10.46: Solve Prob. 10.45, assuming that the length of the tube is increase...
- 10.10.47: column BC that is free at its top C and fixed at its base B. Knowin...
- 10.10.48: A 100-kN axial load P is applied to the W150 3 18 rolled-steelcolum...
- 10.10.49: Axial loads of magnitude P 5 20 kips are applied parallel to the 65...
- 10.10.50: Axial loads of magnitude P 5 135 kips are applied parallel to thege...
- 10.10.51: A 12-kip axial load is applied with an eccentricity e 5 0.375 in. t...
- 10.10.52: Solve Prob. 10.51, assuming that the 12-kip axial load will beappli...
- 10.10.53: An axial load of magnitude P 5 220 kN is applied at a point located...
- 10.10.54: Solve Prob. 10.53, assuming that the magnitude of the axial loadis ...
- 10.10.55: Axial loads of magnitude P 5 175 kN are applied parallel to thegeom...
- 10.10.56: Solve Prob. 10.55, assuming that e 5 0.16 mm and P 5 155 kN.
- 10.10.57: Using allowable stress design, determine the allowable centric load...
- 10.10.58: A W8 3 31 rolled-steel shape is used for a column of 21-ft effectiv...
- 10.10.59: A steel pipe having the cross section shown is used as a column.Usi...
- 10.10.60: A column is made from half of a W360 3 216 rolled-steel shape,with ...
- 10.10.61: A compression member has the cross section shown and an effectivele...
- 10.10.62: Using the aluminum alloy 2014-T6, determine the largest allowablele...
- 10.10.63: A sawn lumber column with a 7.5 3 5.5-in. cross section has an 18-f...
- 10.10.64: A column having a 3.5-m effective length is made of sawn lumberwith...
- 10.10.65: A compression member of 8.2-ft effective length is obtained bybolti...
- 10.10.66: A compression member of 9-m effective length isobtained by welding ...
- 10.10.67: A compression member of 9-m effective length isobtained by welding ...
- 10.10.68: A column of 18-ft effective length is obtained by connecting fourL3...
- 10.10.69: An aluminum structural tube is reinforced by bolting two plates toi...
- 10.10.70: A rectangular column with a 4.4-m effective length is made ofglued ...
- 10.10.71: For a rod made of the aluminum alloy 2014-T6, select the smallestsq...
- 10.10.72: An aluminum tube of 90-mm outer diameter is to carry a centricload ...
- 10.10.73: A 72-kN centric load must be supported by an aluminum columnas show...
- 10.10.74: The glued laminated column shown is free at its top A and fixed 673...
- 10.10.75: An 18-kip centric load is applied to a rectangular sawn lumber colu...
- 10.10.76: A glue laminated column of 3-m effective length is to be madefrom b...
- 10.10.77: A column of 4.5-m effective length must carry a centric load of900 ...
- 10.10.78: A column of 4.6-m effective length must carry a centric load of525 ...
- 10.10.79: A column of 22.5-ft effective length must carry a centric load of28...
- 10.10.80: A square steel tube having the cross section shown is used as acolu...
- 10.10.81: Solve Prob. 10.80, assuming that the effective length of the column...
- 10.10.82: A centric load P must be supported by the steel bar AB. Using allow...
- 10.10.83: Two 3123 212-in. angles are bolted together as shown for use as aco...
- 10.10.84: Two 89 3 64-mm angles are bolted together as shown for use as acolu...
- 10.10.85: A column with a 5.8-m effective length supports a centric load,with...
- 10.10.86: A rectangular steel tube having the cross section shown is used asa...
- 10.10.87: A steel column of 5.5-m effective length must carry a centric deadl...
- 10.10.88: The steel tube having the cross section shown is used as a column o...
- 10.10.89: An eccentric load is applied at a point 22 mm from the geometricaxi...
- 10.10.90: Solve Prob. 10.89, assuming that the load is applied at a point 40 ...
- 10.10.91: A column of 5.5-m effective length is made of the aluminum alloy201...
- 10.10.92: Solve Prob. 10.91, assuming that the effective length of the column...
- 10.10.93: A sawn-lumber column of 5.0 3 7.5-in. cross section has an effectiv...
- 10.10.94: Solve Prob. 10.93 using the interaction method and an allowablestre...
- 10.10.95: A column of 14-ft effective length consists of a section of steeltu...
- 10.10.96: Solve Prob. 10.95, assuming that the effective length of the column...
- 10.10.97: The compression member AB is made of a steel for which sY 5 250 MPa...
- 10.10.98: The compression member AB is made of a steel for which sY 5250 MPa ...
- 10.10.99: An eccentric load P 5 10 kips is applied at a point 0.8 in. fromthe...
- 10.10.100: Solve Prob. 10.99, assuming that the aluminum alloy used is 2014-T6...
- 10.10.101: A rectangular column is made of a grade of sawn wood that hasan adj...
- 10.10.102: Solve Prob. 10.101, assuming that P 5 105 kN
- 10.10.103: An 11-kip vertical load P is applied at the midpoint of one edgeof ...
- 10.10.104: Solve Prob. 10.103, assuming that the vertical load P is applied at...
- 10.10.105: steel tube of 80-mm outer diameter is to carry a 93-kN load Pwith a...
- 10.10.106: Solve Prob. 10.105, using the interaction method with P 5 165 kN,e ...
- 10.10.107: A compression member of rectangular cross section has an effectivel...
- 10.10.108: Solve Prob. 10.107, assuming that e 5 5 mm.
- 10.10.109: An aluminum tube of 3-in. outside diameter is to carry a load of10 ...
- 10.10.110: Solve Prob. 10.109, using the interaction method of design with ana...
- 10.10.111: A sawn lumber column of rectangular cross section has a 2.2-meffect...
- 10.10.112: Solve Prob. 10.111, assuming that e 5 40 mm.
- 10.10.113: A steel column having a 24-ft effective length is loaded eccentri- ...
- 10.10.114: Solve Prob. 10.113 using the interaction method, assuming thatsY 5 ...
- 10.10.115: A steel column of 7.2-m effective length is to support an 83-kNecce...
- 10.10.116: A steel compression member of 5.8-m effective length is to support ...
- 10.10.117: The rigid bar AD is attached to two springs of constant k and isin ...
- 10.10.118: The steel rod BC is attached to the rigid bar AB and to the fixedsu...
- 10.10.119: Determine (a) the critical load for the steel strut, (b) the dimens...
- 10.10.120: Supports A and B of the pin-ended column shown are at a fixeddistan...
- 10.10.121: Members AB and CD are 30-mm-diameter steel rods, and membersBC and ...
- 10.10.122: The uniform aluminum bar AB has a 20 3 36-mm rectangularcross secti...
- 10.10.123: A column with the cross section shown has a 13.5-ft effectivelength...
- 10.10.124: (a) Considering only buckling in the plane of the structure shownan...
- 10.10.125: An axial load P of magnitude 560 kN is applied at a point on the Re...
- 10.10.126: A column of 17-ft effective length must carry a centric load of235 ...
- 10.10.127: Bar AB is free at its end A and fixed at its base B. Determinethe a...
- 10.10.128: A 43-kip axial load P is applied to the rolled-steel column BC ata ...

# Solutions for Chapter 10: Mechanics of Materials 6th Edition

## Full solutions for Mechanics of Materials | 6th Edition

ISBN: 9780073380285

Solutions for Chapter 10

Get Full Solutions
Solutions for Chapter 10

23

2

Chapter 10 includes 128 full step-by-step solutions. This textbook survival guide was created for the textbook: Mechanics of Materials, edition: 6. Since 128 problems in chapter 10 have been answered, more than 25915 students have viewed full step-by-step solutions from this chapter. Mechanics of Materials was written by and is associated to the ISBN: 9780073380285. This expansive textbook survival guide covers the following chapters and their solutions.

Key Engineering and Tech Terms and definitions covered in this textbook