- 10.10.1: Determine the torque T that causes a maximum shearing stress of 70 ...
- 10.10.2: Determine the maximum shearing stress caused by a torque of magnitu...
- 10.10.3: (a) For the hollow shaft and loading shown, determine the maximum s...
- 10.10.4: (a) Determine the torque that can be applied to a solid shaft of 3....
- 10.10.5: (a) For the 3-in.-diameter solid cylinder and loading shown, determ...
- 10.10.6: (a) Determine the torque that can be applied to a solid shaft of 0....
- 10.10.7: The torques shown are exerted on pulleys A, B, and C. Knowing that ...
- 10.10.8: The shafts of the pulley assembly shown are to be redesigned. Knowi...
- 10.10.9: Knowing that each of the shafts AB, BC, and CD consist of solid cir...
- 10.10.10: Knowing that a 0.40-in.-diameter hole has been drilled through each...
- 10.10.11: Under normal operating conditions, the electric motor exerts a torq...
- 10.10.12: In order to reduce the total mass of the assembly of Prob. 10.11, a...
- 10.10.13: The allowable shearing stress is 15 ksi in the 1.5-in.-diameter ste...
- 10.10.14: The allowable shearing stress is 15 ksi in the steel rod AB and 8 k...
- 10.10.15: The solid rod AB has a diameter dAB 5 60 mm and is made of a steel ...
- 10.10.16: The allowable shearing stress is 50 MPa in the brass rod AB and 25 ...
- 10.10.17: The solid shaft shown is formed of a brass for which the allowable ...
- 10.10.18: Solve Prob. 10.17 assuming that the direction of TC is reversed.
- 10.10.19: Under normal operating conditions a motor exerts a torque of magnit...
- 10.10.20: Under normal operating conditions a motor exerts a torque of magnit...
- 10.10.21: A torque of magnitude T 5 1000 N ? m is applied at D as shown. Know...
- 10.10.22: A torque of magnitude T 5 1000 N ? m is applied at D as shown. Know...
- 10.10.23: Two solid shafts are connected by gears as shown and are made of a ...
- 10.10.24: Two solid shafts are connected by gears as shown and are made of a ...
- 10.10.25: For the aluminum shaft shown (G 5 3.9 3 106 psi), determine (a) the...
- 10.10.26: (a) For the solid steel shaft shown (G 5 11.2 3 106 psi), determine...
- 10.10.27: Determine the largest allowable diameter of a 3-m-long steel rod (G...
- 10.10.28: The ship at A has just started to drill for oil on the ocean floor ...
- 10.10.29: The torques shown are exerted on pulleys A and B. Knowing that the ...
- 10.10.30: The torques shown are exerted on pulleys B, C, and D. Knowing that ...
- 10.10.31: The aluminum rod BC (G 5 3.9 3 106 psi) is bonded to the brass rod ...
- 10.10.32: The solid brass rod AB (G 5 39 GPa) is bonded to the solid aluminum...
- 10.10.33: Two solid steel shafts (G 5 77 GPa) are connected by the gears show...
- 10.10.34: Solve Prob. 10.33 assuming that a change in design of the assembly ...
- 10.10.35: Two shafts, each of 3 4-in. diameter, are connected by the gears sh...
- 10.10.36: Solve Prob. 10.35 assuming that after a design change the radius of...
- 10.10.37: The design specifications of a 1.2-m-long solid transmission shaft ...
- 10.10.38: The design specifications of a 2-m-long solid circular transmission...
- 10.10.39: The design of the gear-and-shaft system shown requires that steel s...
- 10.10.40: In the gear-and-shaft system shown, the diameters of the shafts are...
- 10.10.41: A torque of magnitude T 5 35 kip ? in. is applied at end A of the c...
- 10.10.42: The composite shaft shown is to be twisted by applying a torque T a...
- 10.10.43: The composite shaft shown consists of a 0.2-in.-thick brass jacket ...
- 10.10.44: The composite shaft shown consists of a 0.2-in.-thick brass jacket ...
- 10.10.45: Two solid steel shafts (G 5 77.2 GPa) are connected to a coupling d...
- 10.10.46: Solve Prob. 10.45 assuming that shaft AB is replaced by a hollow sh...
- 10.10.47: At a time when rotation is prevented at the lower end of each shaft...
- 10.10.48: Solve Prob. 10.47 assuming that the 50-N ? m torque is applied to e...
- 10.10.49: Knowing that the internal diameter of the hollow shaft shown is d 5...
- 10.10.50: Knowing that d 5 1.2 in., determine the torque T that causes a maxi...
- 10.10.51: The solid spindle AB has a diameter ds 5 1.5 in. and is made of a s...
- 10.10.52: The solid spindle AB is made of a steel with an allowable shearing ...
- 10.10.53: (a) Determine the torque that can be applied to a solid shaft of 90...
- 10.10.54: Two solid brass rods AB and CD are brazed to a brass sleeve EF. Det...
- 10.10.55: In the bevel-gear system shown, a 5 18.438. Knowing that the allowa...
- 10.10.56: The solid cylindrical steel rod BC of length L 5 24 in. is attached...
- 10.10.57: Two solid steel shafts, each of 30-mm diameter, are connected by th...
- 10.10.58: Two solid steel shafts are fitted with flanges that are then connec...
- 10.10.59: The steel jacket CD has been attached to the 40-mm-diameter steel s...

# Solutions for Chapter 10: Torsion

## Full solutions for Statics and Mechanics of Materials | 1st Edition

ISBN: 9780073380155

Solutions for Chapter 10: Torsion

Get Full Solutions
Solutions for Chapter 10

28

0

This textbook survival guide was created for the textbook: Statics and Mechanics of Materials, edition: 1. Since 59 problems in chapter 10: Torsion have been answered, more than 33179 students have viewed full step-by-step solutions from this chapter. Statics and Mechanics of Materials was written by and is associated to the ISBN: 9780073380155. Chapter 10: Torsion includes 59 full step-by-step solutions. This expansive textbook survival guide covers the following chapters and their solutions.

Key Engineering and Tech Terms and definitions covered in this textbook