- 15.2.F15-1: Determine the minimum dimension a to the nearest mm of the beam's c...
- 15.2.F15-2: Determine the minimum diameter d to the nearest l in. of the rod to...
- 15.2.F15-3: Determine the minimum dimension a to the nearest mm of the beam's c...
- 15.2.F15-4: Determine the minimum dimension h to the nearest k in. of the beam'...
- 15.2.F15-5: Determine the minimum dimension b to the nearest mm of the beam's c...
- 15.2.F15-6: Select the lightest W410shaped section that can safely support the ...
- 15.2.15-1: The beam is made of timber that has an allowable bending stress of ...
- 15.2.15-2: Determine the minimum width of the beam to the nearest ~in. that wi...
- 15.2.15-3: Solve Prob. 15-2 if P = 10 kip.
- 15.2.15-4: The brick wall exerts a uniform distributed load of 1.20 kip/ft on ...
- 15.2.15-5: Select the lightest-weight wide-flange beam from Appendix B that wi...
- 15.2.15-6: The spreader beam AB is used to slowly lift the 3000-lb pipe that i...
- 15.2.15-7: Select the lightest-weight wide-flange beam with the shortest depth...
- 15.2.15-8: Select the lightest-weight wide-flange beam from Appendix B that wi...
- 15.2.15-9: Select the lightest W360 wide-flange beam from Appendix B that can ...
- 15.2.15-10: Investigate if the W250 x 58 beam can safely support the loading. T...
- 15.2.15-11: The beam is constructed from two boards. If each nail can support a...
- 15.2.15-12: The joists of a floor in a warehouse are to be selected using squar...
- 15.2.15-13: The timber beam has a width of 6 in. Determine its height h so that...
- 15.2.15-14: The beam is constructed from four boards. If each nail can support ...
- 15.2.15-15: The beam is constructed from two boards. If each nail can support a...
- 15.2.15-16: If the cable is subjected to a maximum force of P = 50 kN, select t...
- 15.2.15-17: If the W360 x 45 wide-flange beam has an allowable normal stress of...
- 15.2.15-18: If P = 800 lb, determine the minimum dimension a of the beam's cros...
- 15.2.15-19: If a = 3 in. and the wood has an allowable normal stress of u a11o ...
- 15.2.15-20: The beam is constructed from three plastic strips. If the glue can ...
- 15.2.15-21: If the allowable bending stress is u allow = 6 MPa, and the glue ca...
- 15.2.15-22: The beam is made of Douglas fir having an allowable bending stress ...
- 15.2.15-23: Select the lightest-weight wide-flange beam from Appendix B that wi...
- 15.2.15-24: Draw the shear and moment diagrams for the shaft, and determine its...
- 15.2.15-25: Draw the shear and moment diagrams for the shaft, and determine its...

# Solutions for Chapter 15.2: Prismatic Beam Design

## Full solutions for Statics and Mechanics of Materials | 5th Edition

ISBN: 9780134382593

Solutions for Chapter 15.2: Prismatic Beam Design

Get Full Solutions
Solutions for Chapter 15.2

29

2

Statics and Mechanics of Materials was written by and is associated to the ISBN: 9780134382593. Since 31 problems in chapter 15.2: Prismatic Beam Design have been answered, more than 40536 students have viewed full step-by-step solutions from this chapter. Chapter 15.2: Prismatic Beam Design includes 31 full step-by-step solutions. This expansive textbook survival guide covers the following chapters and their solutions. This textbook survival guide was created for the textbook: Statics and Mechanics of Materials, edition: 5.

Key Engineering and Tech Terms and definitions covered in this textbook