- 8.8.1: A W10 3 39 rolled-steel beam supports a load P as shown. Knowing th...
- 8.8.2: Solve Prob. 8.1, assuming that P 5 22.5 kips and a 5 20 in.
- 8.8.3: An overhanging W920 3 449 rolled-steel beam supports a load P as sh...
- 8.8.4: Solve Prob. 8.3, assuming that P 5 850 kN and a 5 2.0 m.
- 8.8.5: (a) Knowing that sall 5 160 MPa and tall 5 100 MPa, select the most...
- 8.8.6: (a) Knowing that sall 5 160 MPa and tall 5 100 MPa, select the most...
- 8.8.7: (a) Knowing that sall 5 24 ksi and tall 5 14.5 ksi, select the most...
- 8.8.8: (a) Knowing that sall 5 24 ksi and tall 5 14.5 ksi, select the most...
- 8.8.9: Loading of Prob. 5.73 and selected W530 3 92 shape
- 8.8.10: Loading of Prob. 5.74 and selected W250 3 28.4 shape.
- 8.8.11: Loading of Prob. 5.75 and selected S12 3 31.8 shape
- 8.8.12: Loading of Prob. 5.76 and selected S15 3 42.9 shape.
- 8.8.13: Loading of Prob. 5.77 and selected S510 3 98.2 shape.
- 8.8.14: Loading of Prob. 5.78 and selected S460 3 81.4 shape
- 8.8.15: Determine the smallest allowable diameter of the solid shaft ABCD, ...
- 8.8.16: Determine the smallest allowable diameter of the solid shaft ABCD, ...
- 8.8.17: Using the notation of Sec. 8.2 and neglecting the effect of shearin...
- 8.8.18: The 4-kN force is parallel to the x axis, and the force Q is parall...
- 8.8.19: The vertical force P1 and the horizontal force P2 are applied as sh...
- 8.8.20: The two 500-lb forces are vertical and the force P is parallel to t...
- 8.8.21: It was stated in Sec. 8.2 that the shearing stresses produced in a ...
- 8.8.22: Assuming that the magnitudes of the forces applied to disks A and C...
- 8.8.23: The solid shaft AB rotates at 600 rpm and transmits 80 kW from the ...
- 8.8.24: Solve Prob. 8.23, assuming that shaft AB rotates at 720 rpm.
- 8.8.25: he solid shafts ABC and DEF and the gears shown are used to transmi...
- 8.8.26: 6 Solve Prob. 8.25, assuming that the motor rotates at 360 rpm
- 8.8.27: The solid shaft ABC and the gears shown are used to transmit 10 kW ...
- 8.8.28: Assuming that shaft ABC of Prob. 8.27 is hollow and has an outer di...
- 8.8.29: The solid shaft AE rotates at 600 rpm and transmits 60 hp from the ...
- 8.8.30: Solve Prob. 8.29, assuming that 30 hp is taken off at gear G and 30...
- 8.8.31: Two 1.2-kip forces are applied to an L-shaped machine element AB as...
- 8.8.32: Two 1.2-kip forces are applied to an L-shaped machine element AB as...
- 8.8.33: The cantilever beam AB has a rectangular cross section of 150 3 200...
- 8.8.34: Member AB has a uniform rectangular cross section of 10 3 24 mm. Fo...
- 8.8.35: Member AB has a uniform rectangular cross section of 10 3 24 mm. Fo...
- 8.8.36: Member AB has a uniform rectangular cross section of 10 3 24 mm. Fo...
- 8.8.37: A 1.5-kip force and a 9-kip ? in. couple are applied at the top of ...
- 8.8.38: Two forces are applied to the pipe AB as shown. Knowing that the pi...
- 8.8.39: Several forces are applied to the pipe assembly shown. Knowing that...
- 8.8.40: The steel pile AB has a 100-mm outer diameter and an 8-mm wall thic...
- 8.8.41: Three forces are applied to a 4-in.-diameter plate that is attached...
- 8.8.42: The steel pipe AB has a 72-mm outer diameter and a 5-mm wall thickn...
- 8.8.43: A 13-kN force is applied as shown to the 60-mm-diameter castiron po...
- 8.8.44: A vertical force P of magnitude 60 lb is applied to the crank at po...
- 8.8.45: Three forces are applied to the bar shown. Determine the normal and...
- 8.8.46: Solve Prob. 8.45, assuming that h 5 12 in.
- 8.8.47: Three forces are applied to the bar shown. Determine the normal and...
- 8.8.48: Solve Prob. 8.47, assuming that the 750-N force is directed vertica...
- 8.8.49: Two forces are applied to the small post BD as shown. Knowing that ...
- 8.8.50: Solve Prob. 8.49, assuming that the magnitude of the 6000-lb force ...
- 8.8.51: Three forces are applied to the machine component ABD as shown. Kno...
- 8.8.52: Solve Prob. 8.51, assuming that the magnitude of the 2.5-kN force i...
- 8.8.53: Three steel plates, each 13 mm thick, are welded together to form a...
- 8.8.54: Three steel plates, each 13 mm thick, are welded together to form a...
- 8.8.55: Two forces P1 and P2 are applied as shown in directions perpendicul...
- 8.8.56: Two forces P1 and P2 are applied as shown in directions perpendicul...
- 8.8.57: Four forces are applied to a W8 3 28 rolled-steel beam as shown. De...
- 8.8.58: Four forces are applied to a W8 3 28 rolled-steel beam as shown. De...
- 8.8.59: A force P is applied to a cantilever beam by means of a cable attac...
- 8.8.60: A vertical force P is applied at the center of the free end of cant...
- 8.8.61: A 5-kN force P is applied to a wire that is wrapped around bar AB a...
- 8.8.62: Knowing that the structural tube shown has a uniform wall thickness...
- 8.8.63: The structural tube shown has a uniform wall thickness of 0.3 in. K...
- 8.8.64: For the tube and loading of Prob. 8.63, determine the principal str...

# Solutions for Chapter 8: Mechanics of Materials 7th Edition

## Full solutions for Mechanics of Materials | 7th Edition

ISBN: 9780073398235

Solutions for Chapter 8

Get Full Solutions
Solutions for Chapter 8

22

2

This expansive textbook survival guide covers the following chapters and their solutions. Chapter 8 includes 64 full step-by-step solutions. Mechanics of Materials was written by and is associated to the ISBN: 9780073398235. This textbook survival guide was created for the textbook: Mechanics of Materials, edition: 7. Since 64 problems in chapter 8 have been answered, more than 63235 students have viewed full step-by-step solutions from this chapter.

Key Engineering and Tech Terms and definitions covered in this textbook