Answer: Car batteries are often rated in ampere-hours.

Car batteries are often rated in ampere-hours. Does this information designate the amount of (a) current, (b) power, (c) energy, (d) charge, or (e) potential the battery can supply?

Two wires A and B with circular cross sections are made of the same metal and have equal lengths, but the resistance of wire A is three times greater than that of wire B. (i) What is the ratio of the cross-sectional area of A to that of B? (a) 3 (b) !3 (c) 1 (d) 1/!3 (e) 1 3 (ii) What is the ratio of the radius of A to that of B? Choose from the same possibilities as in part (i).

A cylindrical metal wire at room temperature is carrying electric current between its ends. One end is at potential VA 5 50 V, and the other end is at potential VB 5 0 V. Rank the following actions in terms of the change that each one separately would produce in the current from the greatest increase to the greatest decrease. In your ranking, note any cases of equality. (a) Make VA 5 150 V with VB 5 0 V. (b) Adjust VA to triple the power with which the wire converts electrically transmitted energy into internal energy. (c) Double the radius of the wire. (d) Double the length of the wire. (e) Double the Celsius temperature of the wire.

A current-carrying ohmic metal wire has a crosssectional area that gradually becomes smaller from one end of the wire to the other. The current has the same value for each section of the wire, so charge does not accumulate at any one point. (i) How does the drift speed vary along the wire as the area becomes smaller? (a) It increases. (b) It decreases. (c) It remains constant. (ii) How does the resistance per unit length vary along the wire as the area becomes smaller? Choose from the same possibilities as in part (i).

A potential difference of 1.00 V is maintained across a 10.0-V resistor for a period of 20.0 s. What total charge passes by a point in one of the wires connected to the resistor in this time interval? (a) 200 C (b) 20.0 C (c) 2.00 C (d) 0.005 00 C (e) 0.050 0 C

Three wires are made of copper having circular cross sections. Wire 1 has a length L and radius r. Wire 2 has a length L and radius 2r. Wire 3 has a length 2L and radius 3r. Which wire has the smallest resistance? (a) wire 1 (b) wire 2 (c) wire 3 (d) All have the same resistance. (e) Not enough information is given to answer the question.

A metal wire of resistance R is cut into three equal pieces that are then placed together side by side to form a new cable with a length equal to one-third the original length. What is the resistance of this new cable? (a) 1 9R (b) 1 3R (c) R (d) 3R (e) 9R

A metal wire has a resistance of 10.0 V at a temperature of 20.0C. If the same wire has a resistance of 10.6 V at 90.0C, what is the resistance of this wire when its temperature is 220.0C? (a) 0.700 V (b) 9.66 V (c) 10.3 V (d) 13.8 V (e) 6.59 V

The current-versus-voltage behavior of a certain electrical device is shown in Figure OQ27.9. When the potential difference across the device is 2 V, what is its resistance? (a) 1 V (b) 3 4 V (c) 4 3 V (d) undefined (e) none of those answers

Two conductors made of the same material are connected across the same potential difference. Conductor A has twice the diameter and twice the length of conductor B. What is the ratio of the power delivered to A to the power delivered to B? (a) 8 (b) 4 (c) 2 (d) 1 (e) 1 2

Two conducting wires A and B of the same length and radius are connected across the same potential difference. Conductor A has twice the resistivity of conductor B. What is the ratio of the power delivered to A to the p

Two lightbulbs both operate on 120 V. One has a power of 25 W and the other 100 W. (i) Which lightbulb has higher resistance? (a) The dim 25-W lightbulb does. (b) The bright 100-W lightbulb does. (c) Both are the same. (ii) Which lightbulb carries more current? Choose from the same possibilities as in part (i).

Wire B has twice the length and twice the radius of wire A. Both wires are made from the same material. If wire A has a resistance R, what is the resistance of wire B? (a) 4R (b) 2R (c) R (d) 1 2R (e) 1 4R

A lightbulb has a resistance of 240 V when operating with a potential difference of 120 V across it. What is the current in the lightbulb?

A wire 50.0 m long and 2.00 mm in diameter is connected to a source with a potential difference of 9.11 V, and the current is found to be 36.0 A. Assume a temperature of 20.0C and, using Table 27.2, identify the metal out of which the wire is made.

A 0.900-V potential difference is maintained across a 1.50-m length of tungsten wire that has a crosssectional area of 0.600 mm2. What is the current in the wire?

An electric heater carries a current of 13.5 A when operating at a voltage of 120 V. What is the resistance of the heater?

Aluminum and copper wires of equal length are found to have the same resistance. What is the ratio of their radii?

Suppose you wish to fabricate a uniform wire from 1.00 g of copper. If the wire is to have a resistance of R 5 0.500 V and all the copper is to be used, what must be (a) the length and (b) the diameter of this wire?

Suppose you wish to fabricate a uniform wire from a mass m of a metal with density rm and resistivity r. If the wire is to have a resistance of R and all the metal is to be used, what must be (a) the length and (b) the diameter of this wire?

A portion of Nichrome wire of radius 2.50 mm is to be used in winding a heating coil. If the coil must draw a current of 9.25 A when a voltage of 120 V is applied across its ends, find (a) the required resistance of the coil and (b) the length of wire you must use to wind the coil.

If the current carried by a conductor is doubled, what happens to (a) the charge carrier density, (b) the current density, (c) the electron drift velocity, and (d) the average time interval between collisions?

A current density of 6.00 3 10213 A/m2 exists in the atmosphere at a location where the electric field is 100 V/m. Calculate the electrical conductivity of the Earths atmosphere in this region.

An iron wire has a cross-sectional area equal to 5.00 3 1026 m2. Carry out the following steps to determine the drift speed of the conduction electrons in the wire if it carries a current of 30.0 A. (a) How many kilograms are there in 1.00 mole of iron? (b) Starting with the density of iron and the result of part (a), compute the molar density of iron (the number of moles of iron per cubic meter). (c) Calculate the number density of iron atoms using Avogadros number. (d) Obtain the number density of conduction electrons given that there are two conduction electrons per iron atom. (e) Calculate the drift speed of conduction electrons in this wire.

If the magnitude of the drift velocity of free electrons in a copper wire is 7.84 3 1024 m/s, what is the electric field in the conductor?

A certain lightbulb has a tungsten filament with a resistance of 19.0 V when at 20.0C and 140 V when hot. Assume the resistivity of tungsten varies linearly with temperature even over the large temperature range involved here. Find the temperature of the hot filament.

What is the fractional change in the resistance of an iron filament when its temperature changes from 25.0C to 50.0C?

While taking photographs in Death Valley on a day when the temperature is 58.0C, Bill Hiker finds that a certain voltage applied to a copper wire produces a current of 1.00 A. Bill then travels to Antarctica and applies the same voltage to the same wire. What current does he register there if the temperature is 288.0C? Assume that no change occurs in the wires shape and size.

If a certain silver wire has a resistance of 6.00 V at 20.0C, what resistance will it have at 34.0C?

Plethysmographs are devices used for measuring changes in the volume of internal organs or limbs. In one form of this device, a rubber capillary tube with an inside diameter of 1.00 mm is filled with mercury at 20.0C. The resistance of the mercury is measured with the aid of electrodes sealed into the ends of the tube. If 100 cm of the tube is wound in a helix around a patients upper arm, the blood flow during a heartbeat causes the arm to expand, stretching the length of the tube by 0.040 0 cm. From this observation and assuming cylindrical symmetry, you can find the change in volume of the arm, which gives an indication of blood flow. Taking the resistivity of mercury to be 9.58 3 1027 V ? m, calculate (a) the resistance of the mercury and (b) the fractional change in resistance during the heartbeat. Hint: The fraction by which the cross-sectional area of the mercury column decreases is the fraction by which the length increases because the volume of mercury is constant.

(a) A 34.5-m length of copper wire at 20.0C has a radius of 0.25 mm. If a potential difference of 9.00 V is applied across the length of the wire, determine the current in the wire. (b) If the wire is heated to 30.0C while the 9.00-V potential difference is maintained, what is the resulting current in the wire?

An engineer needs a resistor with a zero overall temperature coefficient of resistance at 20.0C. She designs a pair of circular cylinders, one of carbon and one of Nichrome as shown in Figure P27.32 (page 828). The device must have an overall resistance of R11R25 10.0 V independent of temperature and a uniform radius of r 5 1.50 mm. Ignore thermal expansion of the cylinders and assume both are always at the same temperature. (a) Can she meet the design goal with this method? (b) If so, state what you can determine about the lengths,1 and ,2 of each segment. If not, explain.

An aluminum wire with a diameter of 0.100 mm has a uniform electric field of 0.200 V/m imposed along its entire length. The temperature of the wire is 50.0C. Assume one free electron per atom. (a) Use the information in Table 27.2 to determine the resistivity of aluminum at this temperature. (b) What is the current density in the wire? (c) What is the total current in the wire? (d) What is the drift speed of the conduction electrons? (e) What potential difference must exist between the ends of a 2.00-m length of the wire to produce the stated electric field?

Review. An aluminum rod has a resistance of 1.23 V at 20.0C. Calculate the resistance of the rod at 120C by accounting for the changes in both the resistivity and the dimensions of the rod. The coefficient of linear expansion for aluminum is 2.40 3 1026 (C)21.

At what temperature will aluminum have a resistivity that is three times the resistivity copper has at room temperature?

Assume that global lightning on the Earth constitutes a constant current of 1.00 kA between the ground and an atmospheric layer at potential 300 kV. (a) Find the power of terrestrial lightning. (b) For comparison, find the power of sunlight falling on the Earth. Sunlight has an intensity of 1 370 W/m2 above the atmosphere. Sunlight falls perpendicularly on the circular projected area that the Earth presents to the Sun.

In a hydroelectric installation, a turbine delivers 1 500 hp to a generator, which in turn transfers 80.0% of the mechanical energy out by electrical transmission. Under these conditions, what current does the generator deliver at a terminal potential difference of 2 000 V?

A Van de Graaff generator (see Fig. 25.23) is operating so that the potential difference between the highpotential electrode B and the charging needles at A is 15.0 kV. Calculate the power required to drive the belt against electrical forces at an instant when the effective current delivered to the high-potential electrode is 500 mA.

A certain waffle iron is rated at 1.00 kW when connected to a 120-V source. (a) What current does the waffle iron carry? (b) What is its resistance?

The potential difference across a resting neuron in the human body is about 75.0 mV and carries a current of about 0.200 mA. How much power does the neuron release?

Suppose your portable DVD player draws a current of 350 mA at 6.00 V. How much power does the player require?

Review. A well-insulated electric water heater warms 109 kg of water from 20.0C to 49.0C in 25.0 min. Find the resistance of its heating element, which is connected across a 240-V potential difference.

A 100-W lightbulb connected to a 120-V source experiences a voltage surge that produces 140 V for a moment. By what percentage does its power output increase? Assume its resistance does not change.

The cost of energy delivered to residences by electrical transmission varies from $0.070/kWh to $0.258/kWh throughout the United States; $0.110/kWh is the average value. At this average price, calculate the cost of (a) leaving a 40.0-W porch light on for two weeks while you are on vacation, (b) making a piece of dark toast in 3.00 min with a 970-W toaster, and (c) drying a load of clothes in 40.0 min in a 5.20 3 103-W dryer.

Batteries are rated in terms of ampere-hours (A ? h). For example, a battery that can produce a current of 2.00 A for 3.00 h is rated at 6.00 A ? h. (a) What is the total energy, in kilowatt-hours, stored in a 12.0-V battery rated at 55.0 A ? h? (b) At $0.110 per kilowatt-hour, what is the value of the electricity produced by this battery?

Residential building codes typically require the use of 12-gauge copper wire (diameter 0.205 cm) for wiring receptacles. Such circuits carry currents as large as 20.0 A. If a wire of smaller diameter (with a higher gauge number) carried that much current, the wire could rise to a high temperature and cause a fire. (a) Calculate the rate at which internal energy is produced in 1.00 m of 12-gauge copper wire carrying 20.0 A. (b) What If? Repeat the calculation for a 12-gauge aluminum wire. (c) Explain whether a 12-gauge aluminum wire would be as safe as a copper wire.

Assuming the cost of energy from the electric company is $0.110/kWh, compute the cost per day of operating a lamp that draws a current of 1.70 A from a 110-V line.

An 11.0-W energy-efficient fluorescent lightbulb is designed to produce the same illumination as a conventional 40.0-W incandescent lightbulb. Assuming a cost of $0.110/kWh for energy from the electric company, how much money does the user of the energyefficient bulb save during 100 h of use?

A coil of Nichrome wire is 25.0 m long. The wire has a diameter of 0.400 mm and is at 20.0C. If it carries a current of 0.500 A, what are (a) the magnitude of the electric field in the wire and (b) the power delivered to it? (c) What If? If the temperature is increased to 340C and the potential difference across the wire remains constant, what is the power delivered?

Review. A rechargeable battery of mass 15.0 g delivers an average current of 18.0 mA to a portable DVD player at 1.60V for 2.40 h before the battery must be recharged. The recharger maintains a potential difference of 2.30 V across the battery and delivers a charging current of 13.5 mA for 4.20 h. (a) What is the efficiency of the battery as an energy storage device? (b) How much internal energy is produced in the battery during one chargedischarge cycle? (c) If the battery is surrounded by ideal thermal insulation and has an effective specific heat of 975 J/kg ? C, by how much will its temperature increase during the cycle?

A 500-W heating coil designed to operate from 110 V is made of Nichrome wire 0.500 mm in diameter. (a) Assuming the resistivity of the Nichrome remains constant at its 20.0C value, find the length of wire used. (b) What If? Now consider the variation of resistivity with temperature. What power is delivered to the coil of part (a) when it is warmed to 1 200C?

Why is the following situation impossible? A politician is decrying wasteful uses of energy and decides to focus on energy used to operate plug-in electric clocks in the United States. He estimates there are 270 million of these clocks, approximately one clock for each person in the population. The clocks transform energy taken in by electrical transmission at the average rate 2.50 W. The politician gives a speech in which he complains that, at todays electrical rates, the nation is losing $100 million every year to operate these clocks.

A certain toaster has a heating element made of Nichrome wire. When the toaster is first connected to a 120-V source (and the wire is at a temperature of 20.0C), the initial current is 1.80 A. The current decreases as the heating element warms up. When the toaster reaches its final operating temperature, the current is 1.53 A. (a) Find the power delivered to the toaster when it is at its operating temperature. (b) What is the final temperature of the heating element?

Make an order-of-magnitude estimate of the cost of one persons routine use of a handheld hair dryer for 1 year. If you do not use a hair dryer yourself, observe or interview someone who does. State the quantities you estimate and their values.

Review. The heating element of an electric coffee maker operates at 120 V and carries a current of 2.00 A. Assuming the water absorbs all the energy delivered to the resistor, calculate the time interval during which the temperature of 0.500 kg of water rises from room temperature (23.0C) to the boiling point.

A 120-V motor has mechanical power output of 2.50 hp. It is 90.0% efficient in converting power that it takes in by electrical transmission into mechanical power. (a) Find the current in the motor. (b) Find the energy delivered to the motor by electrical transmission in 3.00 h of operation. (c) If the electric company charges $0.110/kWh, what does it cost to run the motor for 3.00 h?

A particular wire has a resistivity of 3.0 3 1028 V ? m and a cross-sectional area of 4.0 3 1026 m2. A length of this wire is to be used as a resistor that will receive 48 W of power when connected across a 20-V battery. What length of wire is required?

Determine the temperature at which the resistance of an aluminum wire will be twice its value at 20.0C. Assume its coefficient of resistivity remains constant.

A car owner forgets to turn off the headlights of his car while it is parked in his garage. If the 12.0-V battery in his car is rated at 90.0 A ? h and each headlight requires 36.0 W of power, how long will it take the battery to completely discharge?

Lightbulb A is marked 25 W 120 V, and lightbulb B is marked 100 W 120 V. These labels mean that each lightbulb has its respective power delivered to it when it is connected to a constant 120-V source. (a) Find the resistance of each lightbulb. (b) During what time interval does 1.00 C pass into lightbulb A? (c) Is this charge different upon its exit versus its entry into the lightbulb? Explain. (d) In what time interval does 1.00 J pass into lightbulb A? (e) By what mechanisms does this energy enter and exit the lightbulb? Explain. (f) Find the cost of running lightbulb A continuously for 30.0 days, assuming the electric company sells its product at $0.110 per kWh.

One wire in a high-voltage transmission line carries 1 000 A starting at 700 kV for a distance of 100 mi. If the resistance in the wire is 0.500 V/mi, what is the power loss due to the resistance of the wire?

An experiment is conducted to measure the electrical resistivity of Nichrome in the form of wires with different lengths and cross-sectional areas. For one set of measurements, a student uses 30-gauge wire, which has a cross-sectional area of 7.30 3 1028 m2. The student measures the potential difference across the wire and the current in the wire with a voltmeter and an ammeter, respectively. (a) For each set of measurements given in the table taken on wires of three different lengths, calculate the resistance of the wires and the corresponding values of the resistivity. (b) What is the average value of the resistivity? (c) Explain how this value compares with the value given in Table 27.2.

A charge Q is placed on a capacitor of capacitance C. The capacitor is connected into the circuit shown in Figure P27.63, with an open switch, a resistor, and an initially uncharged capacitor of capacitance 3C. The switch is then closed, and the circuit comes to equilibrium. In terms of Q and C, find (a) the final potential difference between the plates of each capacitor, (b) the charge on each capacitor, and (c) the final energy stored in each capacitor. (d) Find the internal energy appearing in the resistor.

Review. An office worker uses an immersion heater to warm 250 g of water in a light, covered, insulated cup from 20.0C to 100C in 4.00 min. The heater is a Nichrome resistance wire connected to a 120-V power supply. Assume the wire is at 100C throughout the 4.00-min time interval. (a) Specify a relationship between a diameter and a length that the wire can have. (b) Can it be made from less than 0.500 cm3 of Nichrome?

An x-ray tube used for cancer therapy operates at 4.00 MV with electrons constituting a beam current of 25.0 mA striking a metal target. Nearly all the power in the beam is transferred to a stream of water flowing through holes drilled in the target. What rate of flow, in kilograms per second, is needed if the rise in temperature of the water is not to exceed 50.0C?

An all-electric car (not a hybrid) is designed to run from a bank of 12.0-V batteries with total energy storage of 2.00 3 107 J. If the electric motor draws 8.00 kW as the car moves at a steady speed of 20.0 m/s, (a) what is the current delivered to the motor? (b) How far can the car travel before it is out of juice?

A straight, cylindrical wire lying along the x axis has a length of 0.500 m and a diameter of 0.200 mm. It is made of a material described by Ohms law with a resistivity of r 5 4.00 3 1028 V ? m. Assume a potential of 4.00 V is maintained at the left end of the wire at x 5 0. Also assume V 5 0 at x 5 0.500 m. Find (a) the magnitude and direction of the electric field in the wire, (b) the resistance of the wire, (c) the magnitude and direction of the electric current in the wire, and (d) the current density in the wire. (e) Show that E 5 rJ

A straight, cylindrical wire lying along the x axis has a length L and a diameter d. It is made of a material described by Ohms law with a resistivity r. Assume potential V is maintained at the left end of the wire at x 5 0. Also assume the potential is zero at x 5 L. In terms of L, d, V, r, and physical constants, derive expressions for (a) the magnitude and direction of the electric field in the wire, (b) the resistance of the wire, (c) the magnitude and direction of the electric current in the wire, and (d) the current density in the wire. (e) Show that E 5 rJ

An electric utility company supplies a customers house from the main power lines (120 V) with two copper wires, each of which is 50.0 m long and has a resistance of 0.108 V per 300 m. (a) Find the potential difference at the customers house for a load current of 110 A. For this load current, find (b) the power delivered to the customer and (c) the rate at which internal energy is produced in the copper wires.

The strain in a wire can be monitored and computed by measuring the resistance of the wire. Let Li represent the original length of the wire, Ai its original cross-sectional area, Ri 5 rLi/Ai the original resistance between its ends, and d 5 DL/Li 5 (L 2 Li)/Li the strain resulting from the application of tension. Assume the resistivity and the volume of the wire do not change as the wire stretches. (a) Show that the resistance between the ends of the wire under strain is given by R 5 Ri (1 1 2d 1 d2). (b) If the assumptions are precisely true, is this result exact or approximate? Explain your answer.

An oceanographer is studying how the ion concentration in seawater depends on depth. She makes a measurement by lowering into the water a pair of concentric metallic cylinders (Fig. P27.71) at the end of a cable and taking data to determine the resistance between these electrodes as a function of depth. The water between the two cylinders forms a cylindrical shell of inner radius ra , outer radius rb , and length L much larger than rb . The scientist applies a potential difference DV between the inner and outer surfaces, producing an outward radial current I. Let r represent the resistivity of the water. (a) Find the resistance of the water between the cylinders in terms of L, r, ra , and rb . (b) Express the resistivity of the water in terms of the measured quantities L, ra , rb , DV, and I

Why is the following situation impossible? An inquisitive physics student takes a 100-W incandescent lightbulb out of its socket and measures its resistance with an ohmmeter. He measures a value of 10.5 V. He is able to connect an ammeter to the lightbulb socket to correctly measure the current drawn by the bulb while operating. Inserting the bulb back into the socket and operating the bulb from a 120-V source, he measures the current to be 11.4 A

The temperature coefficients of resistivity a in Table 27.2 are based on a reference temperature T0 of 20.0C. Suppose the coefficients were given the symbol a9 and were based on a T0 of 0C. What would the coefficient a9 for silver be? Note: The coefficient a satisfies r 5 r0[1 1 a(T 2 T0)], where r0 is the resistivity of the material at T0 5 20.0C. The coefficient a9 must satisfy the expression r 5 r90[1 1 a9T], where r90 is the resistivity of the material at 0C.

A close analogy exists between the flow of energy by heat because of a temperature difference (see Section 20.7) and the flow of electric charge because of a potential difference. In a metal, energy dQ and electrical charge dq are both transported by free electrons. Consequently, a good electrical conductor is usually a good thermal conductor as well. Consider a thin conducting slab of thickness dx, area A, and electrical conductivity s, with a potential difference dV between opposite faces. (a) Show that the current I 5 dq/dt is given by the equation on the left: Charge conduction Thermal conduction dq dt 5 sA ` dV dx ` dQ dt 5 kA ` dT dx ` In the analogous thermal conduction equation on the right (Eq. 20.15), the rate dQ /dt of energy flow by heat (in SI units of joules per second) is due to a temperature gradient dT/dx in a material of thermal conductivity k. (b) State analogous rules relating the direction of the electric current to the change in potential and relating the direction of energy flow to the change in temperature.

Review. When a straight wire is warmed, its resistance is given by R 5 R0[1 1 a(T 2 T0)] according to Equation 27.20, where a is the temperature coefficient of resistivity. This expression needs to be modified if we include the change in dimensions of the wire due to thermal expansion. For a copper wire of radius 0.100 0 mm and length 2.000 m, find its resistance at 100.0C, including the effects of both thermal expansion and temperature variation of resistivity. Assume the coefficients are known to four significant figures.

Review. When a straight wire is warmed, its resistance is given by R 5 R0[1 1 a(T 2 T0)] according to Equation 27.20, where a is the temperature coefficient of resistivity. This expression needs to be modified if we include the change in dimensions of the wire due to thermal expansion. Find a more precise expression for the resistance, one that includes the effects of changes in the dimensions of the wire when it is warmed. Your final expression should be in terms of R0, T, T0, the temperature coefficient of resistivity a, and the coefficient of linear expansion a9

Review. A parallel-plate capacitor consists of square plates of edge length , that are separated by a distance d, where d ,, ,. A potential difference DV is maintained between the plates. A material of dielectric constant k fills half the space between the plates. The dielectric slab is withdrawn from the capacitor as shown in Figure P27.77. (a) Find the capacitance when the left edge of the dielectric is at a distance x from the center of the capacitor. (b) If the dielectric is removed at a constant speed v, what is the current in the circuit as the dielectric is being withdrawn?

The dielectric material between the plates of a parallelplate capacitor always has some nonzero conductivity s. Let A represent the area of each plate and d the distance between them. Let k represent the dielectric constant of the material. (a) Show that the resistance R and the capacitance C of the capacitor are related by RC 5 kP0 s (b) Find the resistance between the plates of a 14.0-nF capacitor with a fused quartz dielectric.

Gold is the most ductile of all metals. For example, one gram of gold can be drawn into a wire 2.40 km long. The density of gold is 19.3 3 103 kg/m3, and its resistivity is 2.44 3 1028 V ? m. What is the resistance of such a wire at 20.0C?

The currentvoltage characteristic curve for a semiconductor diode as a function of temperature T is given by I 5 I0(ee DV/kBT 2 1) Here the first symbol e represents Eulers number, the base of natural logarithms. The second e is the magnitude of the electron charge, the kB stands for Boltzmanns constant, and T is the absolute temperature. (a) Set up a spreadsheet to calculate I and R 5 DV/I for DV 5 0.400 V to 0.600 V in increments of 0.005 V. Assume I0 5 1.00 nA. (b) Plot R versus DV for T 5 280 K, 300 K, and 320 K.

The potential difference across the filament of a lightbulb is maintained at a constant value while equilibrium temperature is being reached. The steady-state current in the bulb is only one-tenth of the current drawn by the bulb when it is first turned on. If the temperature coefficient of resistivity for the bulb at 20.0C is 0.004 50 (C)21 and the resistance increases linearly with increasing temperature, what is the final operating temperature of the filament?

A more general definition of the temperature coefficient of resistivity is a 5 1 r dr dT where r is the resistivity at temperature T. (a) Assuming a is constant, show that r 5 r0e a(T 2 T0) where r0 is the resistivity at temperature T0. (b) Using the series expansion e x < 1 1 x for x ,, 1, show that the resistivity is given approximately by the expression r 5 r0[1 1 a(T 2 T0)] for a(T 2 T0) ,, 1

A spherical shell with inner radius ra and outer radius rb is formed from a material of resistivity r. It carries current radially, with uniform density in all directions. Show that its resistance is R 5 r 4p a 1 ra 2 1 rb b

Material with uniform resistivity r is formed into a wedge as shown in Figure P27.84. Show that the resistance between face A and face B of this wedge is R 5 r L w1y2 2 y12 ln y2 y1

A material of resistivity r is formed into the shape of a truncated cone of height h as shown in Figure P27.85. The bottom end has radius b, and the top end has radius a. Assume the current is distributed uniformly over any circular cross section of the cone so that the current density does not depend on radial position. (The current density does vary with position along the axis of the cone.) Show that the resistance between the two ends is R 5 r p a h abb