A 2.00 kg particle has the xy coordinates (%1.20 m, 0.500 m), and a 4.00 kg particle has the xy coordinates (0.600 m, %0.750 m). Both lie on a horizontal plane. At what (a) x and (b) y coordinates must you place a 3.00 kg particle such that the center of mass of the three-particle system has the coordinates (%0.500 m,%0.700 m)?
Read more- Physics / Fundamentals of Physics 10 / Chapter 9 / Problem 17
Textbook Solutions for Fundamentals of Physics
Question
In Fig. 9-45a, a 4.5 kg dog stands on an 18 kg flatboat at distance D ! 6.1 m from the shore. It walks 2.4 m along the boat toward shore and then stops. Assuming no friction between the boat and the water, find how far the dog is then from the shore.(Hint: See Fig.9-45b.)
Solution
Step 1 of 2
There is no net horizontal force on the dog-boat system, so their centre of mass does not move.
Therefore
Which implies that the
full solution
In Fig. 9-45a, a 4.5 kg dog stands on an 18 kg flatboat at
Chapter 9 textbook questions
-
Chapter 9: Problem 1 Fundamentals of Physics 10
-
Chapter 9: Problem 2 Fundamentals of Physics 10
Figure 9-35 shows a three-particle system, with masses m1 ! 3.0 kg, m2 ! 4.0 kg, and m3 ! 8.0 kg. The scales on the axes are set by xs ! 2.0 m and ys ! 2.0 m.What are (a) the x coordinate and (b) the y coordinate of the systems center of mass? (c) If m3 is gradually increased, does the center of mass of the system shift toward or away from that particle, or does it remain stationary?
Read more -
Chapter 9: Problem 3 Fundamentals of Physics 10
Figure 9-36 shows a slab with dimensions d1 ! 11.0 cm, d2 ! 2.80 cm, and d3 ! 13.0 cm. Half the slab consists of aluminum (density ! 2.70 g/cm3) and half consists of iron (density ! 7.85 g/cm3).What are (a) the x coordinate, (b) the y coordinate, and (c) the z coordinateof the slabs center of mass?
Read more -
Chapter 9: Problem 4 Fundamentals of Physics 10
In Fig. 9-37, three uniform thin rods, each of length L ! 22 cm, form an inverted U. The vertical rods each have a mass of 14 g; the horizontal rod has a mass of 42 g. What are (a) the x coordinate and (b) the y coordinate of the systems center of mass?
Read more -
Chapter 9: Problem 5 Fundamentals of Physics 10
What are (a) the x coordinate and (b) the y coordinate of the center of mass for the uniform plate shown in Fig. 9-38 if L ! 5.0 cm?
Read more -
Chapter 9: Problem 6 Fundamentals of Physics 10
Figure 9-39 shows a cubical box that has been constructed from uniform metal plate of negligible thickness. The box is open at the top and has edge length L ! 40 cm. Find (a) the x coordinate, (b) the y coordinate, and (c) the z coordinate of the center of mass of the box
Read more -
Chapter 9: Problem 7 Fundamentals of Physics 10
In the ammonia (NH3) molecule of Fig. 9-40, three hydrogen (H) atoms form an equilateral triangle, with the center of the triangle at distance d ! 9.40 $ 10%11 m from each hydrogen atom. The nitrogen (N) atom is at the apex of a pyramid, with the three hydrogen atoms forming the base. The nitrogen- to-hydrogen atomic mass ratio is 13.9, and the nitrogen-to-hydrogen distance is L ! 10.14 $ 10%11 m. What are the (a) x and (b) y coordinates of the molecules center of mass?
Read more -
Chapter 9: Problem 8 Fundamentals of Physics 10
A uniform soda can of mass 0.140 kg is 12.0 cm tall and filled with 0.354 kg of soda (Fig. 9-41). Then small holes are drilled in the top and bottom (with negligible loss of metal) to drain the soda. What is the height h of the com of the can and contents (a) initially and (b) after the can loses all the soda? (c) What happens to h as the soda drains out? (d) If x is the height of the remaining soda at any given instant, find x when the com reaches its lowest point.
Read more -
Chapter 9: Problem 9 Fundamentals of Physics 10
A stone is dropped at t ! 0. A second stone, with twice the mass of the first, is dropped from the same point at t ! 100 ms. (a) How far below the release point is the center of mass of the two stones at t ! 300 ms? (Neither stone has yet reached the ground.) (b) How fast is the center of mass of the twostone system moving at that time?
Read more -
Chapter 9: Problem 10 Fundamentals of Physics 10
A 1000 kg automobile is at rest at a traffic signal. At the instant the light turns green, the automobile starts to move with a constant acceleration of 4.0 m/s2 . At the same instant a 2000 kg truck, traveling at a constant speed of 8.0 m/s, overtakes and passes the automobile. (a) How far is the com of the automobiletruck system from the traffic light at t ! 3.0 s? (b) What is the speed of the com then?
Read more -
Chapter 9: Problem 11 Fundamentals of Physics 10
A big olive (m ! 0.50 kg) lies at the origin of an xy coordinate system, and a big Brazil nut (M ! 1.5 kg) lies at the point (1.0, 2.0) m. At t ! 0, a force begins to act on the olive, and a force begins to act on the nut. In unit-vector notation, what is the displacement of the center of mass of the olivenut system at t ! 4.0 s, with respect to its position at t ! 0?
Read more -
Chapter 9: Problem 12 Fundamentals of Physics 10
Two skaters, one with mass 65 kg and the other with mass 40 kg, stand on an ice rink holding a pole of length 10 m and negligible mass. Starting from the ends of the pole, the skaters pull themselves along the pole until they meet. How far does the 40 kg skater move?
Read more -
Chapter 9: Problem 13 Fundamentals of Physics 10
A shell is shot with an initial velocity of 20 m/s, at an angle of with the horizontal. At the top of the trajectory, the shell explodes into two fragments of equal mass (Fig. 9-42). One fragment, whose speed immediately after the explosion is zero, falls vertically. How far from the gun does the other fragment land, assuming that the terrain is level and that air drag is negligible?
Read more -
Chapter 9: Problem 14 Fundamentals of Physics 10
In Figure 9-43, two particles are launched from the origin of the coordinate system at time t ! 0. Particle 1 of mass m1 ! 5.00 g is shot directly along the x axis on a frictionless floor, with constant speed 10.0 m/s. Particle 2 of mass m2 ! 3.00 g is shot with a velocity of magnitude 20.0 m/s, at an upward angle such that it always stays directly above particle 1. (a) What is the maximum height Hmax reached by the com of the two-particle system? In unit-vector notation, what are the (b) velocity and (c) acceleration of the com when the com reaches Hmax?
Read more -
Chapter 9: Problem 15 Fundamentals of Physics 10
Figure 9-44 shows an arrangement with an air track, in which a cart is connected by a cord to a hanging block. The cart has mass m1 ! 0.600 kg, and its center is initially at xy coordinates (%0.500 m, 0 m); the block has mass m2 ! 0.400 kg, and its center is initially at xy coordinates (0,%0.100 m).The mass of the cord and pulley are negligible. The cart is released from rest, and both cart and block move until the cart hits the pulley. The friction between the cart and the air track and between the pulley and its axle is negligible. (a) In unit-vector notation, what is the acceleration of the center of mass of the cartblock system? (b) What is the velocity of the com as a function of time t? (c) Sketch the path taken by the com. (d) If the path is curved, determine whether it bulges upward to the right or downward to the left, and if it is straight, find the angle between it and the x axis.
Read more -
Chapter 9: Problem 16 Fundamentals of Physics 10
Ricardo, of mass 80 kg, and Carmelita, who is lighter, are enjoying Lake Merced at dusk in a 30 kg canoe.When the canoe is at rest in the placid water, they exchange seats, which are 3.0 m apart and symmetrically located with respect to the canoes center. If the canoe moves 40 cm horizontally relative to a pier post, what is Carmelitas mass?
Read more -
Chapter 9: Problem 17 Fundamentals of Physics 10
In Fig. 9-45a, a 4.5 kg dog stands on an 18 kg flatboat at distance D ! 6.1 m from the shore. It walks 2.4 m along the boat toward shore and then stops. Assuming no friction between the boat and the water, find how far the dog is then from the shore.(Hint: See Fig.9-45b.)
Read more -
Chapter 9: Problem 18 Fundamentals of Physics 10
A 0.70 kg ball moving horizontally at 5.0 m/s strikes a vertical wall and rebounds with speed 2.0 m/s.What is the magnitude of the change in its linear momentum?
Read more -
Chapter 9: Problem 19 Fundamentals of Physics 10
A 2100 kg truck traveling north at 41 km/h turns east and accelerates to 51 km/h. (a) What is the change in the trucks kinetic energy? What are the (b) magnitude and (c) direction of the change in its momentum?
Read more -
Chapter 9: Problem 20 Fundamentals of Physics 10
At time t ! 0, a ball is struck at ground level and sent over level ground.The momentum p versust during the flight is given by Fig. 9-46 (with and ). At what initial angle is the ball launched? (Hint: Find a solution that does not require you to read the time of the low point of the plot.)
Read more -
Chapter 9: Problem 21 Fundamentals of Physics 10
A 0.30 kg softball has a velocity of 15 m/s at an angle of 35# below the horizontal just before making contact with the bat.What is the magnitude of the change in momentum of the ball while in contact with the bat if the ball leaves with a velocity of (a) 20 m/s, vertically downward,and (b) 20 m/s,horizontally back toward the pitcher?
Read more -
Chapter 9: Problem 22 Fundamentals of Physics 10
Figure 9-47 gives an overhead view of the path taken by a 0.165 kg cue ball as it bounces from a rail of a pool table. The balls initial speed is 2.00 m/s, and the angle u1 is 30.0#.The bounce reverses the y component of the balls velocity but does not alter the x component. What are (a) angle u2 and (b) the change in the balls linear momentum in unit-vector notation? (The fact that the ball rolls is irrelevant to the problem.)
Read more -
Chapter 9: Problem 23 Fundamentals of Physics 10
Until his seventies, Henri LaMothe (Fig. 9-48) excited audiences by belly-flopping from a height of 12 m into 30 cm of water. Assuming that he stops just as he reaches the bottom of the water and estimating his mass, find the magnitude of the impulse on him from the water.
Read more -
Chapter 9: Problem 24 Fundamentals of Physics 10
In February 1955, a paratrooper fell 370 m from an airplane without being able to open his chute but happened to land in snow, suffering only minor injuries. Assume that his speed at impact was 56 m/s (terminal speed), that his mass (including gear) was 85 kg, and that the magnitude of the force on him from the snow was at the survivable limit of 1.2 $ 105 N. What are (a) the minimum depth of snow that would have stopped him safely and (b) the magnitude of the impulse on him from the snow?
Read more -
Chapter 9: Problem 25 Fundamentals of Physics 10
A 1.2 kg ball drops vertically onto a floor, hitting with a speed of 25 m/s. It rebounds with an initial speed of 10 m/s. (a) What impulse acts on the ball during the contact? (b) If the ball is in contact with the floor for 0.020 s, what is the magnitude of the average force on the floor from the ball?
Read more -
Chapter 9: Problem 26 Fundamentals of Physics 10
In a common but dangerous prank, a chair is pulled away as a person is moving downward to sit on it, causing the victim to land hard on the floor. Suppose the victim falls by 0.50 m, the mass that moves downward is 70 kg, and the collision on the floor lasts 0.082 s. What are the magnitudes of the (a) impulse and (b) average force acting on the victim from the floor during the collision?
Read more -
Chapter 9: Problem 27 Fundamentals of Physics 10
A force in the negative direction of an x axis is applied for 27 ms to a 0.40 kg ball initially moving at 14 m/s in the positive direction of the axis. The force varies in magnitude, and the impulse has magnitude 32.4 N)s.What are the balls (a) speed and (b) direction of travel just after the force is applied? What are (c) the average magnitude of the force and (d) the direction of the impulse on the ball?
Read more -
Chapter 9: Problem 28 Fundamentals of Physics 10
In tae-kwon-do, a hand is slammed down onto a target at a speed of 13 m/s and comes to a stop during the 5.0 ms collision. Assume that during the impact the hand is independent of the arm and has a mass of 0.70 kg. What are the magnitudes of the (a) impulse and (b) average force on the hand from the target?
Read more -
Chapter 9: Problem 29 Fundamentals of Physics 10
Suppose a gangster sprays Supermans chest with 3 g bullets at the rate of 100 bullets/min, and the speed of each bullet is 500 m/s. Suppose too that the bullets rebound straight back with no change in speed. What is the magnitude of the average force on Supermans chest?
Read more -
Chapter 9: Problem 30 Fundamentals of Physics 10
Two average forces. A steady stream of 0.250 kg snowballs is shot perpendicularly into a wall at a speed of 4.00 m/s. Each ball sticks to the wall. Figure 9-49 gives the magnitude F of the force on the wall as a function of time t for two of the snowball impacts. Impacts occur with a repetition time interval "tr ! 50.0 ms, last a duration time interval "td ! 10 ms, and produce isosceles triangles on the graph, with each impact reaching a force maximum Fmax ! 200 N. During each impact, what are the magnitudes of (a) the impulse and (b) the average force on the wall? (c) During a time interval of many impacts, what is the magnitude of the average force on the wall?
Read more -
Chapter 9: Problem 31 Fundamentals of Physics 10
Jumping up before the elevator hits. After the cable snaps and the safety system fails, an elevator cab free-falls from a height of 36 m. During the collision at the bottom of the elevator shaft, a 90 kg passenger is stopped in 5.0 ms. (Assume that neither the passenger nor the cab rebounds.) What are the magnitudes of the (a) impulse and (b) average force on the passenger during the collision? If the passenger were to jump upward with a speed of 7.0 m/s relative to the cab floor just before the cab hits the bottom of the shaft, what are the magnitudes of the (c) impulse and (d) average force (assuming the same stopping time)?
Read more -
Chapter 9: Problem 32 Fundamentals of Physics 10
A 5.0 kg toy car can move along an x axis; Fig. 9-50 gives Fx of the force acting on the car, which begins at rest at time t ! 0. The scale on the Fx axis is set by In unit-vector notation, what is at (a) t 4.0 s and (b) t 7.0 s, and (c) what is at t 9.0 s?
Read more -
Chapter 9: Problem 33 Fundamentals of Physics 10
Figure 9-51 shows a 0.300 kg baseball just before and just after it collides with a bat. Just before, the ball has velocity of magnitude 12.0 m/s and angle u1 ! 35.0#. Just after, it is traveling directly upward with velocity of magnitude 10.0 m/s. The duration of the collision is 2.00 ms. What are the (a) magnitude and (b) direction (relative to the positive direction of the xaxis) of the impulse on the ball from the bat? What are the (c)magnitude and (d) direction of the average force on the ball from the bat?
Read more -
Chapter 9: Problem 34 Fundamentals of Physics 10
Basilisk lizards can run across the top of a water surface (Fig. 9-52). With each step, a lizard first slaps its foot against the water and then pushes it down into the water rapidly enough to form an air cavity around the top of the foot. To avoid having to pull the foot back up against water drag in order to complete the step, the lizard withdraws the foot before water can flow into the air cavity. If the lizard is not to sink, the average upward impulse on the lizard during this full action of slap, downward push, and withdrawal must match the downward impulse due to the gravitational force. Suppose the mass of a basilisk lizard is 90.0 g, the mass of each foot is 3.00 g, the speed of a foot as it slaps the water is 1.50 m/s, and the time for a single step is 0.600 s. (a) What is the magnitude of the impulse on the lizard during the slap? (Assume this impulse is directly upward.) (b) During the 0.600 s duration of a step, what is the downward impulse on the lizard due to the gravitational force? (c) Which action, the slap or the push, provides the primary support for the lizard, or are they approximately equal in their support?
Read more -
Chapter 9: Problem 35 Fundamentals of Physics 10
Figure 9-53 shows an approximate plot of force magnitude F versus time t during the collision of a 58 g Superball with a wall. The initial velocity of the ball is 34 m/s perpendicular to the wall; the ball rebounds directly back with approximately the same speed, also perpendicular to the wall. What is Fmax, the maximum magnitude of the force on the ball from the wall during the collision?
Read more -
Chapter 9: Problem 36 Fundamentals of Physics 10
A 0.25 kg puck is initially stationary on an ice surface with negligible friction. At time t ! 0, a horizontal force begins to move the puck. The force is given by ! (12.0 % , with in newtons and t in seconds, and it acts until its magnitude is zero. (a) What is the magnitude of the impulse on the puck from the force between t ! 0.500 s and t ! 1.25 s? (b) What is the change in momentum of the puck between t ! 0 and the instant at which F ! 0?
Read more -
Chapter 9: Problem 37 Fundamentals of Physics 10
A soccer player kicks a soccer ball of mass 0.45 kg that is initially at rest. The foot of the player is in contact with the ball for 3.0 $ 10%3 s, and the force of the kick is given by F(t) ! [(6.0 $ 106 )t % (2.0 $ 109 )t 2 ] N for 0 ( t ( 3.0 $ 10%3 s, where t is in seconds. Find the magnitudes of (a) the impulse on the ball due to the kick, (b) the average force on the ball from the players foot during the period of contact, (c) the maximum force on the ball from the players foot during the period of contact, and (d) the balls velocity immediately after it loses contact with the players foot.
Read more -
Chapter 9: Problem 38 Fundamentals of Physics 10
In the overhead view of Fig. 9-54, a 300 g ball with a speed v of 6.0 m/s strikes a wall at an angle u of 30# and then rebounds with the same speed and angle. It is in contact with the wall for 10 ms. In unitvector notation, what are (a) the impulse on the ball from the wall and (b) the average force on the wall from the ball?
Read more -
Chapter 9: Problem 39 Fundamentals of Physics 10
A 91 kg man lying on a surface of negligible friction shoves a 68 g stone away from himself, giving it a speed of 4.0 m/s. What speed does the man acquire as a result?
Read more -
Chapter 9: Problem 40 Fundamentals of Physics 10
Find \(dy/dx\). \(y=\int_{1}^{e^{\sqrt{x}}} \ln \left(t^{2}+1\right) d t\) Equation Transcription: Text Transcription: dy/dx y = integral_1^e sqrt x ln (t^2 +1) dt
Read more -
Chapter 9: Problem 41 Fundamentals of Physics 10
Figure 9-55 shows a two-ended rocket that is initially stationary on a frictionless floor, with its center at the origin of an x axis.The rocket consists of a central block C (of mass M ! 6.00 kg) and blocks L and R (each of mass m ! 2.00 kg) on the left and right sides. Small explosions can shoot either of the side blocks away from block C and along the x axis. Here is the sequence: (1) At time t ! 0, block L is shot to the left with a speed of 3.00 m/s relative to the velocity that the explosion gives the rest of the rocket. (2) Next, at time t ! 0.80 s, block R is shot to the right with a speed of 3.00 m/s relative to the velocity that block C then has. At t ! 2.80 s, what are (a) the velocity of block C and (b) the position of its center?
Read more -
Chapter 9: Problem 42 Fundamentals of Physics 10
An object, with mass m and speed v relative to an observer, explodes into two pieces, one three times as massive as the other; the explosion takes place in deep space. The less massive piece stops relative to the observer. How much kinetic energy is added to the system during the explosion, as measured in the observers reference frame?
Read more -
Chapter 9: Problem 43 Fundamentals of Physics 10
In the Olympiad of 708 B.C., some athletes competing in the standing long jump used handheld weights called halteres to lengthen their jumps (Fig. 9-56).The weights were swung up in front just before liftoff and then swung down and thrown backward during the flight. Suppose a modern 78 kg long jumper similarly uses two 5.50 kg halteres, throwing them horizontally to the rear at his maximum height such that their horizontal velocity is zero relative to the ground. Let his liftoff velocity be m/s with or without the halteres, and assume that he lands at the liftoff level. What distance would the use of the halteres add to his range?
Read more -
Chapter 9: Problem 44 Fundamentals of Physics 10
In Fig. 9-57, a stationary block explodes into two pieces L and R that slide across a frictionless floor and then into regions with friction, where they stop. Piece L, with a mass of 2.0 kg, encounters a coefficient of kinetic friction mL ! 0.40 and slides to a stop in distance dL ! 0.15 m. Piece R encounters a coefficient of kinetic friction mR ! 0.50 and slides to a stop in distance dR ! 0.25 m. What was the mass of the block?
Read more -
Chapter 9: Problem 45 Fundamentals of Physics 10
A 20.0 kg body is moving through space in the positive direction of an x axis with a speed of 200 m/s when, due to an internal explosion, it breaks into three parts. One part, with a mass of 10.0 kg, moves away from the point of explosion with a speed of 100 m/s in the positive y direction. A second part, with a mass of 4.00 kg, moves in the negative x direction with a speed of 500 m/s. (a) In unit-vector notation, what is the velocity of the third part? (b) How much energy is released in the explosion? Ignore effects due to the gravitational force.
Read more -
Chapter 9: Problem 46 Fundamentals of Physics 10
A 4.0 kg mess kit sliding on a frictionless surface explodes into two 2.0 kg parts: 3.0 m/s, due north, and 5.0 m/s, 30# north of east.What is the original speed of the mess kit?
Read more -
Chapter 9: Problem 47 Fundamentals of Physics 10
A vessel at rest at the origin of an xy coordinate system explodes into three pieces. Just after the explosion, one piece, of mass m, moves with velocity (%30 m/s) and a second piece, also of mass m, moves with velocity (%30 m/s) . The third piece has mass 3m. Just after the explosion, what are the (a) magnitude and (b) direction of the velocity of the third piece?
Read more -
Chapter 9: Problem 48 Fundamentals of Physics 10
Particle A and particle B are held together with a compressed spring between them. When they are released, the spring pushes them apart, and they then fly off in opposite directions, free of the spring. The mass of A is 2.00 times the mass of B, and the energy stored in the spring was 60 J. Assume that the spring has negligible mass and that all its stored energy is transferred to the particles. Once that transfer is complete, what are the kinetic energies of (a) particle A and (b) particle B?
Read more -
Chapter 9: Problem 49 Fundamentals of Physics 10
A bullet of mass 10 g strikes a ballistic pendulum of mass 2.0 kg. The center of mass of the pendulum rises a vertical distance of 12 cm. Assuming that the bullet remains embedded in the pendulum, calculate the bullets initial speed.
Read more -
Chapter 9: Problem 50 Fundamentals of Physics 10
A 5.20 g bullet moving at 672 m/s strikes a 700 g wooden block at rest on a frictionless surface. The bullet emerges, traveling in the same direction with its speed reduced to 428 m/s. (a) What is the resulting speed of the block? (b) What is the speed of the bulletblock center of mass?
Read more -
Chapter 9: Problem 51 Fundamentals of Physics 10
In Fig. 9-58a, a 3.50 g bullet is fired horizontally at two blocks at rest on a frictionless table.The bullet passes through block 1 (mass 1.20 kg) and embeds itself in block 2 (mass 1.80 kg). The blocks end up with speeds v1 ! 0.630 m/s and v2 ! 1.40 m/s (Fig. 9-58b). Neglecting the material removed from block 1 by the bullet, find the speed of the bullet as it (a) leaves and (b) enters block 1.
Read more -
Chapter 9: Problem 52 Fundamentals of Physics 10
In Fig. 9-59, a 10 g bullet moving directly upward at 1000 m/s strikes and passes through the center of mass of a 5.0 kg block initially at rest. The bullet emerges from the block moving directly upward at 400 m/s. To what maximum height does the block then rise above its initial position?
Read more -
Chapter 9: Problem 53 Fundamentals of Physics 10
In Anchorage, collisions of a vehicle with a moose are so common that they are referred to with the abbreviation MVC. Suppose a 1000 kg car slides into a stationary 500 kg moose on a very slippery road, with the moose being thrown through the windshield (a common MVC result). (a) What percent of the original kinetic energy is lost in the collision to other forms of energy? A similar danger occurs in Saudi Arabia because of camelvehicle collisions (CVC). (b) What percent of the original kinetic energy is lost if the car hits a 300 kg camel? (c) Generally, does the percent loss increase or decrease if the animal mass decreases?
Read more -
Chapter 9: Problem 54 Fundamentals of Physics 10
A completely inelastic collision occurs between two balls of wet putty that move directly toward each other along a vertical axis. Just before the collision, one ball, of mass 3.0 kg, is moving upward at 20 m/s and the other ball, of mass 2.0 kg, is moving downward at 12 m/s. How high do the combined two balls of putty rise above the collision point? (Neglect air drag.)
Read more -
Chapter 9: Problem 55 Fundamentals of Physics 10
A 5.0 kg block with a speed of 3.0 m/s collides with a 10 kg block that has a speed of 2.0 m/s in the same direction.After the collision, the 10 kg block travels in the original direction with a speed of 2.5 m/s. (a) What is the velocity of the 5.0 kg block immediately after the collision? (b) By how much does the total kinetic energy of the system of two blocks change because of the collision? (c) Suppose, instead, that the 10 kg block ends up with a speed of 4.0 m/s. What then is the change in the total kinetic energy? (d) Account for the result you obtained in (c).
Read more -
Chapter 9: Problem 56 Fundamentals of Physics 10
In the before part of Fig. 9-60, car A (mass 1100 kg) is stopped at a traffic light when it is rear-ended by car B (mass 1400 kg). Both cars then slide with locked wheels until the frictional force from the slick road (with a low mk of 0.13) stops them, at distances dA ! 8.2 m and dB ! 6.1 m. What are the speeds of (a) car A and (b) car B at the start of the sliding, just after the collision? (c) Assuming that linear momentum is conserved during the collision, find the speed of car B just before the collision. (d) Explain why this assumption may be invalid.
Read more -
Chapter 9: Problem 57 Fundamentals of Physics 10
In Fig. 9-61, a ball of mass Figure 9-60 Problem 56. A B A B dA dB Before After v0 vi m M Figure 9- 61 Problem 57. m ! 60 g is shot with speed vi 22 m/s into the barrel of a spring gun of mass M 240 g initially at rest on a frictionless surface.The ball sticks in ! ! the barrel at the point of maximum compression of the spring. Assume that the increase in thermal energy due to friction between the ball and the barrel is negligible. (a) What is the speed of the spring gun after the ball stops in the barrel? (b) What fraction of the initial kinetic energy of the ball is stored in the spring?
Read more -
Chapter 9: Problem 58 Fundamentals of Physics 10
In Fig. 9-62, block 2 (mass 1.0 kg) is at rest on a frictionless surface and touching the end of an unstretched spring of spring constant 200 N/m.The other end of the spring is fixed to a wall. Block 1 (mass 2.0 kg), traveling at speed v1 ! 4.0 m/s, collides with block 2, and the two blocks stick together.When the blocks momentarily stop, by what distance is the spring compressed?
Read more -
Chapter 9: Problem 59 Fundamentals of Physics 10
In Fig. 9-63, block 1 (mass 2.0 kg) is moving rightward at 10 m/s and block 2 (mass 5.0 kg) is moving rightward at 3.0 m/s. The surface is frictionless, and a spring with a spring constant of 1120 N/m is fixed to block 2. When the blocks collide, the compression of the spring is maximum at the instant the blocks have the same velocity. Find the maximum compression.
Read more -
Chapter 9: Problem 60 Fundamentals of Physics 10
In Fig. 9-64, block A (mass 1.6 kg) slides into block B (mass 2.4 kg), along a frictionless surface. The directions of three velocities before (i) and after (f) the collision are indicated; the corresponding speeds are vAi 5.5 m/s, vBi 2.5 m/s, and vBf 4.9 m/s. What are the (a) speed and (b) direction (left or right) of velocity ? (c) Is the collision elastic?
Read more -
Chapter 9: Problem 61 Fundamentals of Physics 10
A cart with mass 340 g moving on a frictionless linear air track at an initial speed of 1.2 m/s undergoes an elastic collision with an initially stationary cart of unknown mass. After the collision, the first cart continues in its original direction at 0.66 m/s. (a) What is the mass of the second cart? (b) What is its speed after impact? (c) What is the speed of the twocart center of mass?
Read more -
Chapter 9: Problem 62 Fundamentals of Physics 10
Two titanium spheres approach each other head-on with the same speed and collide elastically. After the collision, one of the spheres, whose mass is 300 g, remains at rest. (a) What is the mass of the other sphere? (b) What is the speed of the two-sphere center of mass if the initial speed of each sphere is 2.00 m/s?
Read more -
Chapter 9: Problem 63 Fundamentals of Physics 10
Block 1 of mass m1 slides along a frictionless floor and into a one-dimensional elastic collision with stationary block 2 of mass m2 ! 3m1. Prior to the collision, the center of mass of the twoblock system had a speed of 3.00 m/s. Afterward, what are the speeds of (a) the center of mass and (b) block 2?
Read more -
Chapter 9: Problem 64 Fundamentals of Physics 10
A steel ball of mass 0.500 kg is fastened to a cord that is 70.0 cm long and fixed at the far end.The ball is then released when the cord is horizontal (Fig. 9-65). At the bottom of its path, the ball strikes a 2.50 kg steel block initially at rest on a frictionless surface. The collision is elastic. Find (a) the speed of the ball and (b) the speed of the block, both just after the collision
Read more -
Chapter 9: Problem 65 Fundamentals of Physics 10
A body of mass 2.0 kg makes an elastic collision with another body at rest and continues to move in the original direction but with one-fourth of its original speed. (a) What is the mass of the other body? (b) What is the speed of the two-body center of mass if the initial speed of the 2.0 kg body was 4.0 m/s?
Read more -
Chapter 9: Problem 66 Fundamentals of Physics 10
Block 1, with mass m1 and speed 4.0 m/s, slides along an x axis on a frictionless floor and then undergoes a one-dimensional elastic collision with stationary block 2, with mass m2 ! 0.40m1.The two blocks then slide into a region where the coefficient of kinetic friction is 0.50; there they stop. How far into that region do (a) block 1 and (b) block 2 slide?
Read more -
Chapter 9: Problem 67 Fundamentals of Physics 10
In Fig. 9-66, particle 1 of mass m1 ! 0.30 kg slides rightward along an x axis on a frictionless floor with a speed of 2.0 m/s.When it reaches x 0, it undergoes a one-dimensional elastic collision with stationary particle 2 of mass m2 0.40 kg.When particle 2 then reaches a wall at xw 70 cm, it bounces from the wall with no loss of speed. At what position on the x axis does particle 2 then collide with particle 1?
Read more -
Chapter 9: Problem 68 Fundamentals of Physics 10
In Fig. 9-67, block 1 of mass m1 slides from rest along a frictionless ramp from height h 2.50 m and then collides with stationary block 2, which has mass m2 ! 2.00m1.After the collision, block 2 slides into a region where the coefficient of kinetic friction mk is 0.500 and comes to a stop in distance d within that region. What is the value of distance d if the collision is (a) elastic and (b) completely inelastic?
Read more -
Chapter 9: Problem 69 Fundamentals of Physics 10
A small ball of mass m is aligned above a larger ball of mass M ! 0.63 kg (with a slight separation, as with the baseball and basketball of Fig. 9-68a), and the two are dropped simultaneously from a height of h ! 1.8 m. (Assume the radius of each ball is negligible relative to h.) (a) If the larger ball rebounds elastically from the floor and then the small ball rebounds elastically from the larger ball, what value of m results in the larger ball stopping when it collides with the small ball? (b) What height does the small ball then reach (Fig. 9-68b)?
Read more -
Chapter 9: Problem 70 Fundamentals of Physics 10
In Fig. 9-69, puck 1 of mass m1 ! 0.20 kg is sent sliding across a frictionless lab bench, to undergo a one-dimensional elastic collision with stationary puck 2. Puck 2 then slides off the bench and lands a distance d from the base of the bench. Puck 1 rebounds from the collision and slides off the opposite edge of the bench, landing a distance 2d from the base of the bench. What is the mass of puck 2? (Hint: Be careful with signs.)
Read more -
Chapter 9: Problem 71 Fundamentals of Physics 10
In Fig. 9-21, projectile particle 1 is an alpha particle and target particle 2 is an oxygen nucleus. The alpha particle is scattered at angle u1 64.0# and the oxygen nucleus recoils with speed 1.20 $ 105 m/s and at angle u2 51.0#. In atomic mass units, the mass of the alpha particle is 4.00 u and the mass of the oxygen nucleus is 16.0 u. What are the (a) final and (b) initial speeds of the alpha particle?
Read more -
Chapter 9: Problem 72 Fundamentals of Physics 10
Ball B, moving in the positive direction of an x axis at speed v, collides with stationary ball A at the origin. A and B have different masses.After the collision, B moves in the negative direction of the y axis at speed v/2. (a) In what direction does A move? (b) Show that the speed of A cannot be determined from the given information.
Read more -
Chapter 9: Problem 73 Fundamentals of Physics 10
After a completely inelastic collision, two objects of the same mass and same initial speed move away together at half their initial speed. Find the angle between the initial velocities of the objects.
Read more -
Chapter 9: Problem 74 Fundamentals of Physics 10
Two 2.0 kg bodies, A and B, collide. The velocities before the collision are and m/s.After the collision, What are (a) the final velocity of B and (b) the change in the total kinetic energy (including sign)?
Read more -
Chapter 9: Problem 75 Fundamentals of Physics 10
A projectile proton with a speed of 500 m/s collides elastically with a target proton initially at rest. The two protons then move along perpendicular paths, with the projectile path at 60# from the original direction. After the collision, what are the speeds of (a) the target proton and (b) the projectile proton?
Read more -
Chapter 9: Problem 76 Fundamentals of Physics 10
A 6090 kg space probe moving nose-first toward Jupiter at 105 m/s relative to the Sun fires its rocket engine, ejecting 80.0 kg of exhaust at a speed of 253 m/s relative to the space probe.What is the final velocity of the probe?
Read more -
Chapter 9: Problem 77 Fundamentals of Physics 10
In Fig. 9-70, two long barges are moving in the same direction in still water, one with a speed of 10 km/h and the other with a speed of 20 km/h. While they are passing each other, coal is shoveled from the slower to the faster one at a rate of 1000 kg/min. How much additional force must be provided by the driving engines of (a) the faster barge and (b) the slower barge if neither is to change speed? Assume that the shoveling is always perfectly sideways and that the frictional forces between the barges and the water do not depend on the mass of the barges
Read more -
Chapter 9: Problem 78 Fundamentals of Physics 10
Consider a rocket that is in deep space and at rest relative to an inertial reference frame. The rockets engine is to be fired for a certain interval. What must be the rockets mass ratio (ratio of initial to final mass) over that interval if the rockets original speed relative to the inertial frame is to be equal to (a) the exhaust speed (speed of the exhaust products relative to the rocket) and (b) 2.0 times the exhaust speed?
Read more -
Chapter 9: Problem 79 Fundamentals of Physics 10
A rocket that is in deep space and initially at rest relative to an inertial reference frame has a mass of 2.55 105 kg, of which 1.81 105 kg is fuel. The rocket engine is then fired for 250 s while fuel is consumed at the rate of 480 kg/s. The speed of the exhaust products relative to the rocket is 3.27 km/s. (a) What is the rockets thrust? After the 250 s firing, what are (b) the mass and (c) the speed of the rocket?
Read more -
Chapter 9: Problem 80 Fundamentals of Physics 10
An object is tracked by a radar station and determined to have a position vector given by ! (3500 % 160t) & 2700 & 300 , with in meters and t in seconds. The radar stations x axis points east, its y axis north, and its z axis vertically up. If the object is a 250 kg meteorological missile, what are (a) its linear momentum, (b) its direction of motion, and (c) the net force on it?
Read more -
Chapter 9: Problem 81 Fundamentals of Physics 10
he last stage of a rocket, which is traveling at a speed of 7600 m/s, consists of two parts that are clamped together: a rocket case with a mass of 290.0 kg and a payload capsule with a mass of 150.0 kg. When the clamp is released, a compressed spring causes the two parts to separate with a relative speed of 910.0 m/s. What are the speeds of (a) the rocket case and (b) the payload after they have separated? Assume that all velocities are along the same line. Find the total kinetic energy of the two parts (c) before and (d) after they separate. (e) Account for the difference.
Read more -
Chapter 9: Problem 82 Fundamentals of Physics 10
Pancake collapse of a tall building. In the section of a tall building shown in Fig. 9-71a, the infrastructure of any given floor K must support the weight W of all higher floors. Normally the infrastructure is constructed with a safety factor s so that it can withstand an even greater downward force of sW. If, however, the support columns between K and L suddenly collapse and allow the higher floors to free-fall together onto floor K (Fig. 9-71b), the force in the collision can exceed sW and, after a brief pause, cause K to collapse onto floor J, which collapses on floor I, and so on until the ground is reached. Assume that the floors are separated by and have the same mass.Also assume that when the floors above K free-fall onto K, the collision lasts 1.5 ms. Under these simplified conditions, what value must the safety factor s exceed to prevent pancake collapse of the building?
Read more -
Chapter 9: Problem 83 Fundamentals of Physics 10
Relative is an important word. In Fig. 9-72, block L of mass mL ! 1.00 kg and block R of mass mR ! 0.500 kg are held in place with a compressed spring between them. When the blocks are released, the spring sends them sliding across a frictionless floor. (The spring has negligible mass and falls to the floor after the blocks leave it.) (a) If the spring gives block L a release speed of 1.20 m/s relative to the floor, how far does block R travel in the next 0.800 s? (b) If, instead, the spring gives block L a release speed of 1.20 m/s relative to the velocity that the spring gives block R, how far does block R travel in the next 0.800 s?
Read more -
Chapter 9: Problem 84 Fundamentals of Physics 10
Figure 9-73 shows an overhead view of two particles sliding at constant velocity over a frictionless surface. The particles have the same mass and the same initial speed v ! 4.00 m/s, and they collide where their paths intersect. An x axis is arranged to bisect the angle between their incoming paths, such that u ! 40.0#. The region to the right of the collision is divided into four lettered sections by the x axis and four numbered dashed lines. In what region or along what line do the particles travel if the collision is (a) completely inelastic, (b) elastic, and (c) inelastic? What are their final speeds if the collision is (d) completely inelastic and (e) elastic?
Read more -
Chapter 9: Problem 85 Fundamentals of Physics 10
Speed deamplifier. In Fig. 9-74, block 1 of mass m1 slides along an x axis on a frictionless floor at speed 4.00 m/s. Then it undergoes a one-dimensional elastic collision with stationary block 2 of mass m2 ! 2.00m1. Next, block 2 undergoes a one-dimensional elastic collision with stationary block 3 of mass m3 ! 2.00m2. (a) What then is the speed of block 3? Are (b) the speed, (c) the kinetic energy, and (d) the momentum of block 3 greater than, less than, or the same as the initial values for block 1?
Read more -
Chapter 9: Problem 86 Fundamentals of Physics 10
Speed amplifier. In Fig. 9-75, block 1 of mass m1 slides along an x axis on a frictionless floor with a speed of v1i 4.00 m/s. Then it undergoes a one-dimensional elastic collision with stationary block 2 of mass m2 ! 0.500m1. Next, block 2 undergoes a one-dimensional elastic collision with stationary block 3 of mass m3 ! 0.500m2. (a) What then is the speed of block 3? Are (b) the speed, (c) the kinetic energy, and (d) the momentum of block 3 greater than, less than, or the same as the initial values for block 1?
Read more -
Chapter 9: Problem 87 Fundamentals of Physics 10
A ball having a mass of 150 g strikes a wall with a speed of 5.2 m/s and rebounds with only 50% of its initial kinetic energy. (a) What is the speed of the ball immediately after rebounding? (b) What is the magnitude of the impulse on the wall from the ball? (c) If the ball is in contact with the wall for 7.6 ms, what is the magnitude of the average force on the ball from the wall during this time interval?
Read more -
Chapter 9: Problem 88 Fundamentals of Physics 10
A spacecraft is separated into two parts by detonating the explosive bolts that hold them together. The masses of the parts are 1200 kg and 1800 kg; the magnitude of the impulse on each part from the bolts is 300 N)s. With what relative speed do the two parts separate because of the detonation?
Read more -
Chapter 9: Problem 89 Fundamentals of Physics 10
A 1400 kg car moving at 5.3 m/s is initially traveling north along the positive direction of a y axis. After completing a 90# right-hand turn in 4.6 s, the inattentive operator drives into a tree, which stops the car in 350 ms. In unit-vector notation, what is the impulse on the car (a) due to the turn and (b) due to the collision? What is the magnitude of the average force that acts on the car (c) during the turn and (d) during the collision? (e) What is the direction of the average force during the turn?
Read more -
Chapter 9: Problem 90 Fundamentals of Physics 10
A certain radioactive (parent) nucleus transforms to a different (daughter) nucleus by emitting an electron and a neutrino. The parent nucleus was at rest at the origin of an xy coordinate system. The electron moves away from the origin with linear momentum (%1.2 $ 10%22 kg )m/s) ; the neutrino moves away from the origin with linear momentum (%6.4 $ 10%23 kg )m/s) . What are the (a) magnitude and (b) direction of the linear momentum of the daughter nucleus? (c) If the daughter nucleus has a mass of 5.8 $ 10%26 kg, what is its kinetic energy?
Read more -
Chapter 9: Problem 91 Fundamentals of Physics 10
A 75 kg man rides on a 39 kg cart moving at a velocity of 2.3 m/s. He jumps off with zero horizontal velocity relative to the ground. What is the resulting change in the carts velocity,including sign?
Read more -
Chapter 9: Problem 92 Fundamentals of Physics 10
Two blocks of masses 1.0 kg and 3.0 kg are connected by a spring and rest on a frictionless surface. They are given velocities toward each other such that the 1.0 kg block travels initially at 1.7 m/s toward the center of mass, which remains at rest. What is the initial speed of the other block?
Read more -
Chapter 9: Problem 93 Fundamentals of Physics 10
A railroad freight car of mass 3.18 $ 104 kg collides with a stationary caboose car. They couple together, and 27.0% of the initial kinetic energy is transferred to thermal energy, sound, vibrations, and so on. Find the mass of the caboose.
Read more -
Chapter 9: Problem 94 Fundamentals of Physics 10
An old Chrysler with mass 2400 kg is moving along a straight stretch of road at 80 km/h. It is followed by a Ford with mass 1600 kg moving at 60 km/h. How fast is the center of mass of the two cars moving?
Read more -
Chapter 9: Problem 95 Fundamentals of Physics 10
In the arrangement of Fig. 9-21, billiard ball 1 moving at a speed of 2.2 m/s undergoes a glancing collision with identical billiard ball 2 that is at rest. After the collision, ball 2 moves at speed 1.1 m/s, at an angle of u2 ! 60#.What are (a) the magnitude and (b) the direction of the velocity of ball 1 after the collision? (c) Do the given data suggest the collision is elastic or inelastic?
Read more -
Chapter 9: Problem 96 Fundamentals of Physics 10
A rocket is moving away from the solar system at a speed of 6.0 $ 103 m/s. It fires its engine, which ejects exhaust with a speed of 3.0 $ 103 m/s relative to the rocket. The mass of the rocket at this time is 4.0 $ 104 kg, and its acceleration is 2.0 m/s2 . (a) What is the thrust of the engine? (b) At what rate, in kilograms per second, is exhaust ejected during the firing?
Read more -
Chapter 9: Problem 97 Fundamentals of Physics 10
The three balls in the overhead view of Fig. 9-76 are identical. Balls 2 and 3 touch each other and are aligned perpendicular to the path of ball 1. The velocity of ball 1 has magnitude v0 ! 10 m/s and is directed at the contact point of balls 1 and 2. After the collision, what are the (a) speed and (b) direction of the velocity of ball 2, the (c) speed and (d) direction of the velocity of ball 3, and the (e) speed and (f) direction of the velocity of ball 1? (Hint: With friction absent, each impulse is directed along the line connecting the centers of the colliding balls, normal to the colliding surfaces.)
Read more -
Chapter 9: Problem 98 Fundamentals of Physics 10
A 0.15 kg ball hits a wall with a velocity of (5.00 m/s) & (6.50 m/s) & (4.00 m/s) . It rebounds from the wall with a velocity of (2.00 m/s) (3.50 m/s) ( 3.20 m/s) . What are (a) the change in the balls momentum, (b) the impulse on the ball, and (c) the impulse on the wall?
Read more -
Chapter 9: Problem 99 Fundamentals of Physics 10
In Fig. 9-77, two identical containers of sugar are connected by a cord that passes over a frictionless pulley. The cord and pulley have negligible mass, each container and its sugar together have a mass of 500 g, the centers of the containers are separated by 50 mm, and the containers are held fixed at the same height. What is the horizontal distance between the center of container 1 and the center of mass of the two-container system (a) initially and (b) after 20 g of sugar is transferred from container 1 to container 2? After the transfer and after the containers are released, (c) in what direction and (d) at what acceleration magnitude does the center of mass move?
Read more -
Chapter 9: Problem 100 Fundamentals of Physics 10
In a game of pool, the cue ball strikes another ball of the same mass and initially at rest. After the collision, the cue ball moves at 3.50 m/s along a line making an angle of 22.0# with the cue balls original direction of motion, and the second ball has a speed of 2.00 m/s. Find (a) the angle between the direction of motion of the second ball and the original direction of motion of the cue ball and (b) the original speed of the cue ball. (c) Is kinetic energy (of the centers of mass, dont consider the rotation) conserved?
Read more -
Chapter 9: Problem 101 Fundamentals of Physics 10
In Fig. 9-78, a 3.2 kg box of running shoes slides on a horizontal frictionless table and collides with a 2.0 kg box of ballet slippers initially at rest on the edge of the table, at height h ! 0.40 m. The speed of the 3.2 kg box is 3.0 m/s just before the collision. If the two boxes stick together because of packing tape on their sides, what is their kinetic energy just before they strike the floor?
Read more -
Chapter 9: Problem 102 Fundamentals of Physics 10
In Fig. 9-79, an 80 kg man is on a ladder hanging from a balloon that has a total mass of 320 kg (including the basket passenger). The balloon is initially stationary relative to the ground. If the man on the ladder begins to climb at 2.5 m/s relative to the ladder, (a) in what direction and (b) at what speed does the balloon move? (c) If the man then stops climbing, what is the speed of the balloon?
Read more -
Chapter 9: Problem 103 Fundamentals of Physics 10
In Fig. 9-80, block 1 of mass m1 ! 6.6 kg is at rest on a long frictionless table that is up against a wall. Block 2 of mass m2 is placed between block 1 and the wall and sent sliding to the left, toward block 1, with constant speed v2i. Find the value of m2 for which both blocks move with the same velocity after block 2 has collided once with block 1 and once with the wall.Assume all collisions are elastic (the collision with the wall does not change the speed of block 2).
Read more -
Chapter 9: Problem 104 Fundamentals of Physics 10
The script for an action movie calls for a small race car (of mass 1500 kg and length 3.0 m) to accelerate along a flattop boat (of mass 4000 kg and length 14 m), from one end of the boat to the other, where the car will then jump the gap between the boat and a somewhat lower dock. You are the technical advisor for the movie. The boat will initially touch the dock, as in Fig. 9-81; the boat can slide through the water without significant resistance; both the car and the boat can be approximated as uniform in their mass distribution. Determine what the width of the gap will be just as the car is about to make the jump.
Read more -
Chapter 9: Problem 105 Fundamentals of Physics 10
A 3.0 kg object moving at 8.0 m/s in the positive direction of an x axis has a one-dimensional elastic collision with an object of mass M, initially at rest. After the collision the object of mass M has a velocity of 6.0 m/s in the positive direction of the axis.What is mass M?
Read more -
Chapter 9: Problem 106 Fundamentals of Physics 10
A 2140 kg railroad flatcar, which can move with negligible friction, is motionless next to a platform. A 242 kg sumo wrestler runs at 5.3 m/s along the platform (parallel to the track) and then jumps onto the flatcar. What is the speed of the flatcar if he then (a) stands on it, (b) runs at 5.3 m/s relative to it in his original direction, and (c) turns and runs at 5.3 m/s relative to the flatcar opposite his original direction?
Read more -
Chapter 9: Problem 107 Fundamentals of Physics 10
A 6100 kg rocket is set for vertical firing from the ground. If the exhaust speed is 1200 m/s, how much gas must be ejected each second if the thrust (a) is to equal the magnitude of the gravitational force on the rocket and (b) is to give the rocket an initial upward acceleration of 21 m/s2 ?
Read more -
Chapter 9: Problem 108 Fundamentals of Physics 10
A 500.0 kg module is attached to a 400.0 kg shuttle craft, which moves at 1000 m/s relative to the stationary main spaceship. Then a small explosion sends the module backward with speed 100.0 m/s relative to the new speed of the shuttle craft. As measured by someone on the main spaceship, by what fraction did the kinetic energy of the module and shuttle craft increase because of the explosion?
Read more -
Chapter 9: Problem 109 Fundamentals of Physics 10
(a) How far is the center of mass of the EarthMoon system from the center of Earth? (Appendix C gives the masses of Earth and the Moon and the distance between the two.) (b) What percentage of Earths radius is that distance?
Read more -
Chapter 9: Problem 110 Fundamentals of Physics 10
A 140 g ball with speed 7.8 m/s strikes a wall perpendicularly and rebounds in the opposite direction with the same speed. The collision lasts 3.80 ms. What are the magnitudes of the (a) impulse and (b) average force on the wall from the ball during the elastic collision?
Read more -
Chapter 9: Problem 111 Fundamentals of Physics 10
A rocket sled with a mass of 2900 kg moves at 250 m/s on a set of rails. At a certain point, a scoop on the sled dips into a trough of water located between the tracks and scoops water into an empty tank on the sled. By applying the principle of conservation of linear momentum, determine the speed of the sled after 920 kg of water has been scooped up. Ignore any retarding force on the scoop.
Read more -
Chapter 9: Problem 112 Fundamentals of Physics 10
A pellet gun fires ten 2.0 g pellets per second with a speed of 500 m/s. The pellets are stopped by a rigid wall. What are (a) the magnitude of the momentum of each pellet, (b) the kinetic energy of each pellet, and (c) the magnitude of the average force on the wall from the stream of pellets? (d) If each pellet is in contact with the wall for 0.60 ms, what is the magnitude of the average force on the wall from each pellet during contact? (e) Why is this average force so different from the average force calculated in (c)?
Read more -
Chapter 9: Problem 113 Fundamentals of Physics 10
A railroad car moves under a grain elevator at a constant speed of 3.20 m/s. Grain drops into the car at the rate of 540 kg/min. What is the magnitude of the force needed to keep the car moving at constant speed if friction is negligible?
Read more -
Chapter 9: Problem 114 Fundamentals of Physics 10
Figure 9-82 shows a uniform square plate of edge length 6d ! 6.0 m from which a square piece of edge length 2d has been removed.What are (a) the x coordinate and (b) the y coordinate of the center of mass of the remaining piece?
Read more -
Chapter 9: Problem 116 Fundamentals of Physics 10
Two particles P and Q are released from rest 1.0 m apart.P has a mass of 0.10 kg, and Q a mass of 0.30 kg.P and Q attract each other with a constant force of 1.0 $ 10%2 N. No external forces act on the system. (a) What is the speed of the center of mass of P and Q when the separation is 0.50 m? (b) At what distance from Ps original position do the particles collide?
Read more -
Chapter 9: Problem 117 Fundamentals of Physics 10
A collision occurs between a 2.00 kg particle traveling with velocity and a 4.00 kg particle traveling with velocity . The collision connects the two particles. What then is their velocity in (a) unit-vector notation and as a (b) magnitude and (c) angle?
Read more -
Chapter 9: Problem 118 Fundamentals of Physics 10
In the two-sphere arrangement of Fig. 9-20, assume that sphere 1 has a mass of 50 g and an initial height of h1 ! 9.0 cm, and that sphere 2 has a mass of 85 g. After sphere 1 is released and collides elastically with sphere 2, what height is reached by (a) sphere 1 and (b) sphere 2? After the next (elastic) collision, what height is reached by (c) sphere 1 and (d) sphere 2? (Hint: Do not use rounded-off values.)
Read more -
Chapter 9: Problem 119 Fundamentals of Physics 10
In Fig. 9-83, block 1 slides along an x axis on a frictionless floor with a speed of 0.75 m/s. When it reaches stationary block 2, the two blocks undergo an elastic collision. The following table gives the mass and length of the (uniform) blocks and also the locations of their centers at time t ! 0. Where is the center of mass of the two-block system located (a) at t ! 0, (b) when the two blocks first touch, and (c) at t ! 4.0 s? Block Mass (kg) Length (cm) Center at t ! 0 1 0.25 5.0 x ! %1.50 m 2 0.50 6.0 x ! 0
Read more -
Chapter 9: Problem 120 Fundamentals of Physics 10
A body is traveling at 2.0 m/s along the positive direction of an x axis; no net force acts on the body. An internal explosion separates the body into two parts, each of 4.0 kg, and increases the total kinetic energy by 16 J. The forward part continues to move in the original direction of motion. What are the speeds of (a) the rear part and (b) the forward part?
Read more -
Chapter 9: Problem 121 Fundamentals of Physics 10
An electron undergoes a one-dimensional elastic collision with an initially stationary hydrogen atom. What percentage of the electrons initial kinetic energy is transferred to kinetic energy of the hydrogen atom? (The mass of the hydrogen atom is 1840 times the mass of the electron.)
Read more -
Chapter 9: Problem 122 Fundamentals of Physics 10
A man (weighing 915 N) stands on a long railroad flatcar (weighing 2415 N) as it rolls at 18.2 m/s in the positive direction of an x axis, with negligible friction. Then the man runs along the flatcar in the negative x direction at 4.00 m/s relative to the flatcar. What is the resulting increase in the speed of the flatcar?
Read more -
Chapter 9: Problem 123 Fundamentals of Physics 10
An unmanned space probe (of mass m and speed v relative to the Sun) approaches the planet Jupiter (of mass M and speed VJ relative to the Sun) as shown in Fig. 9-84. The spacecraft rounds the planet and departs in the opposite direction. What is its speed (in kilometers per second), relative to the Sun, after this slingshot encounter, which can be analyzed as a collision? Assume v ! 10.5 km/s and VJ! 13.0 km/s (the orbital speed of Jupiter).The mass of Jupiter is very much greater than the mass of the spacecraft (M . m)
Read more -
Chapter 9: Problem 124 Fundamentals of Physics 10
A 0.550 kg ball falls directly down onto concrete, hitting it with a speed of 12.0 m/s and rebounding directly upward with a speed of 3.00 m/s. Extend a y axis upward. In unit-vector notation, what are (a) the change in the balls momentum, (b) the impulse on the ball, and (c) the impulse on the concrete?
Read more -
Chapter 9: Problem 125 Fundamentals of Physics 10
An atomic nucleus at rest at the origin of an xy coordinate system transforms into three particles. Particle 1, mass 16.7 $ 10%27 kg, moves away from the origin at velocity (6.00 $ 106 m/s) ; particle 2, mass 8.35 $ 10%27 kg, moves away at velocity (%8.00 $ 106 m/s) . (a) In unit-vector notation, what is the linear momentum of the third particle, mass 11.7 $ 10%27 kg? (b) How much kinetic energy appears in this transformation?
Read more -
Chapter 9: Problem 126 Fundamentals of Physics 10
Particle 1 of mass 200 g and speed 3.00 m/s undergoes a onedimensional collision with stationary particle 2 of mass 400 g.What is the magnitude of the impulse on particle 1 if the collision is (a) elastic and (b) completely inelastic?
Read more -
Chapter 9: Problem 127 Fundamentals of Physics 10
During a lunar mission, it is necessary to increase the speed of a spacecraft by 2.2 m/s when it is moving at 400 m/s relative to the Moon. The speed of the exhaust products from the rocket engine is 1000 m/s relative to the spacecraft. What fraction of the initial mass of the spacecraft must be burned and ejected to accomplish the speed increase?
Read more -
Chapter 9: Problem 128 Fundamentals of Physics 10
A cue stick strikes a stationary pool ball, with an average force of 32 N over a time of 14 ms. If the ball has mass 0.20 kg, what speed does it have just after impact?
Read more