Integrated Concepts Referring to the situation in the

What is the value of the magnetic flux at coil \(2\) in Figure \(23.56\) due to coil \(1\)? Figure \(23.56\) (a) The planes of the two coils are perpendicular. (b) The wire is perpendicular to the plane of the coil. Equation Transcription: Text Transcription: 2 23.56 1

Problem 1CQ How do the multiple-loop coils and iron ring in the version of Faraday’s apparatus shown in Figure 23.3 enhance the observation of induced emf?

Problem 3CQ Explain how magnetic flux can be zero when the magnetic field is not zero.

What is the value of the magnetic flux through the coil in Figure \(23.56\)(b) due to the wire? Figure \(23.56\) (a) The planes of the two coils are perpendicular. (b) The wire is perpendicular to the plane of the coil. Equation Transcription: Text Transcription: 23.56

Referring to Figure \(23.57\)(a), what is the direction of the current induced in coil \(2\): (a) If the current in coil \(1\) increases? (b) If the current in coil \(1\) decreases? (c) If the current in coil \(1\) is constant? Explicitly show how you follow the steps in the Problem-Solving Strategy for Lenz's Law. Figure \(23.57\) (a) The coils lie in the same plane. (b) The wire is in the plane of the coil Equation Transcription: Text Transcription: 23.57 1 2

Problem 106PE Referring to Example 23.14, find the average power at 10.0 kHz. Example 23.14: Calculating the Power Factor and Power For the same RLC series circuit having a 40.0 ? resistor, a 3.00 mH inductor, a 5.00 ?F capacitor, and a voltage source with a Vrms of 120 V: (a) Calculate the power factor and phase angle for f = 60.0Hz . (b) What is the average power at 50.0 Hz? (c) Find the average power at the circuit’s resonant frequency.

Problem 5CQ A person who works with large magnets sometimes places her head inside a strong field. She reports feeling dizzy as she quickly turns her head. How might this be associated with induction?

Referring to Figure \(23.57\)(b), what is the direction of the current induced in the coil: (a) If the current in the wire increases? (b) If the current in the wire decreases? (c) If the current in the wire suddenly changes direction? Explicitly show how you follow the steps in the Problem-Solving Strategy for Lenz’s Law. Figure \(23.57\) (a) The coils lie in the same plane. (b) The wire is in the plane of the coil Equation Transcription: Text Transcription: 23.57

A particle accelerator sends high-velocity charged particles down an evacuated pipe. Explain how a coil of wire wrapped around the pipe could detect the passage of individual particles. Sketch a graph of the voltage output of the coil as a single particle passes through it.

Is an emf induced in the coil in Figure \(23.54\) when it is stretched? If so, state why and give the direction of the induced current. Figure \(23.54\) A circular coil of wire is stretched in a magnetic field. Equation Transcription: Text Transcription: 23.54

Why must part of the circuit be moving relative to other parts, to have usable motional emf? Consider, for example, that the rails in Figure \(23.11\) are stationary relative to the magnetic field, while the rod moves. Equation Transcription: Text Transcription: 23.11

Repeat the previous problem with the battery reversed.

Problem 7PE Verify that the units of ?? / ?t are volts. That is, show that 1 T ? m2 / s = 1 V .

Problem 8PE Suppose a 50-turn coil lies in the plane of the page in a uniform magnetic field that is directed into the page. The coil originally has an area of 0.250 m2 . It is stretched to have no area in 0.100 s. What is the direction and magnitude of the induced emf if the uniform magnetic field has a strength of 1.50 T?

Problem 9CQ An induction stove heats a pot with a coil carrying an alternating current located beneath the pot (and without a hot surface). Can the stove surface be a conductor? Why won’t a coil carrying a direct current work?

Problem 8CQ A powerful induction cannon can be made by placing a metal cylinder inside a solenoid coil. The cylinder is forcefully expelled when solenoid current is turned on rapidly. Use Faraday’s and Lenz’s laws to explain how this works. Why might the cylinder get live/hot when the cannon is fired?

Problem 9PE (a) An MRI technician moves his hand from a region of very low magnetic field strength into an MRI scanner’s 2.00 T field with his fingers pointing in the direction of the field. Find the average emf induced in his wedding ring, given its diameter is 2.20 cm and assuming it takes 0.250 s to move it into the field. (b) Discuss whether this current would significantly change the temperature of the ring.

Problem 10CQ Explain how you could thaw out a frozen water pipe by wrapping a coil carrying an alternating current around it. Does it matter whether or not the pipe is a conductor? Explain.

Problem 10PE Integrated Concepts Referring to the situation in the previous problem: (a) What current is induced in the ring if its resistance is 0.0100 ? ? (b) What average power is dissipated? (c) What magnetic field is induced at the center of the ring? (d) What is the direction of the induced magnetic field relative to the MRI’s field?

Problem 11CQ Explain why magnetic damping might not be effective on an object made of several thin conducting layers separated by insulation.

Using \(RHR-1\), show that the emfs in the sides of the generator loop in Figure \(23.23\) are in the same sense and thus add. Equation Transcription: Text Transcription: RHR-1 23.23

Problem 12PE A 0.250 m radius, 500-turn coil is rotated one-fourth of a revolution in 4.17 ms, originally having its plane perpendicular to a uniform magnetic field. (This is 60 rev/s.) Find the magnetic field strength needed to induce an average emf of 10,000 V.

Integrated Concepts Approximately how does the emf induced in the loop in Figure \(23.57\)(b) depend on the distance of the center of the loop from the wire? Equation Transcription: Text Transcription: 23.57

Problem 11PE An emf is induced by rotating a 1000-turn, 20.0 cm diameter coil in the Earth’s 5.00×10?5 T magnetic field. What average emf is induced, given the plane of the coil is originally perpendicular to the Earth’s field and is rotated to be parallel to the field in 10.0 ms?

Problem 14CQ The source of a generator’s electrical energy output is the work done to turn its coils. How is the work needed to turn the generator related to Lenz’s law?

Integrated Concepts (a) A lightning bolt produces a rapidly varying magnetic field. If the bolt strikes the earth vertically and acts like a current in a long straight wire, it will induce a voltage in a loop aligned like that in Figure \(23.57\)(b). What voltage is induced in a \(1.00 m\) diameter loop \(50.0 m\) from a \(2.00 \times 10^{6} \mathrm{~A}\) lightning strike, if the current falls to zero in \(25.0 \mu \mathrm{s}\) ? (b) Discuss circumstances under which such a voltage would produce noticeable consequences. Equation Transcription: Text Transcription: 23.57 1.00 m 50.0 m 2.00 times 10^6 A 25.0 mu s

Problem 15CQ Suppose you find that the belt drive connecting a powerful motor to an air conditioning unit is broken and the motor is running freely. Should you be worried that the motor is consuming a great deal of energy for no useful purpose? Explain why or why not.

Problem 12CQ Explain how electromagnetic induction can be used to detect metals? This technique is particularly important in detecting buried landmines for disposal, geophysical prospecting and at airports.

Use Faraday’s law, Lenz’s law, and \(RHR-1\) to show that the magnetic force on the current in the moving rod in Figure \(23.11\) is in the opposite direction of its velocity. Equation Transcription: Text Transcription: RHR-1 23.11

Problem 16CQ Explain what causes physical vibrations in transformers at twice the frequency of the AC power involved.

Problem 17CQ Does plastic insulation on live/hot wires prevent shock hazards, thermal hazards, or both?

Problem 17PE (a) A jet airplane with a 75.0 m wingspan is flying at 280 m/s. What emf is induced between wing tips if the vertical component of the Earth’s field is 3.00×10?5 T ? (b) Is an emf of this magnitude likely to have any consequences? Explain.

Problem 19CQ A GFI may trip just because the live/hot and neutral wires connected to it are significantly different in length. Explain why.

Problem 18CQ Why are ordinary circuit breakers and fuses ineffective in preventing shocks?

If a current flows in the Satellite Tether shown in Figure \(23.12\), use Faraday’s law, Lenz’s law, and \(RHR-1\) to show that there is a magnetic force on the tether in the direction opposite to its velocity. Equation Transcription: Text Transcription: 23.12 RHR-1

Problem 18PE (a) A nonferrous screwdriver is being used in a 2.00 T magnetic field. What maximum emf can be induced along its 12.0 cm length when it moves at 6.00 m/s? (b) Is it likely that this emf will have any consequences or even be noticed?

At what speed must the sliding rod in Figure \(23.11\) move to produce an emf of \(1.00 V\) in a \(1.50 T\) field, given the rod’s length is \(30.0 cm\)? Equation Transcription: Text Transcription: 23.11 1.00 V 1.50 T 30.0 cm

Problem 20CQ How would you place two identical flat coils in contact so that they had the greatest mutual inductance? The least?

Problem 21CQ How would you shape a given length of wire to give it the greatest self-inductance? The least?

Problem 21PE Prove that when B , l , and v are not mutually perpendicular, motional emf is given by emf = Blvsin ? . If v is perpendicular to B , then ? is the angle between l and B . If l is perpendicular to B , then ? is the angle between v and B .

Problem 23CQ Presbycusis is a hearing loss due to age that progressively affects higher frequencies. A hearing aid amplifier is designed to amplify all frequencies equally. To adjust its output for presbycusis, would you put a capacitor in series or parallel with the hearing aid’s speaker? Explain.

Problem 24CQ Would you use a large inductance or a large capacitance in series with a system to filter out low frequencies, such as the 100 Hz hum in a sound system? Explain.

Problem 22CQ Verify, as was concluded without proof in Example 23.7, that units of T ? m2 / A = ? ? s = H. Example 23.7: Calculating the Self-inductance of a Moderate Size Solenoid Calculate the self-inductance of a 10.0 cm long, 4.00 cm diameter solenoid that has 200 coils.

In the August \(1992\) space shuttle flight, only \(250 m\) of the conducting tether considered in Example \(23.2\) could be let out. A \(40.0 V\) motional emf was generated in the Earth’s \(5.00 \times 10^{-5} \mathrm{~T}\) field, while moving at \(7.80 \times 10^{3} \mathrm{~m} / \mathrm{s}\) . What was the angle between the shuttle’s velocity and the Earth’s field, assuming the conductor was perpendicular to the field? Equation Transcription: Text Transcription: 1992 250 m 23.2 40.0 V 5.00 times 10^-5 T 7.80 times 10^3 m/s

Integrated Concepts Derive an expression for the current in a system like that in Figure \(23.11\), under the following conditions. The resistance between the rails is \(R\) , the rails and the moving rod are identical in cross section \(A\) and have the same resistivit \(\rho\) . The distance between the rails is \(\text { ? }\), and the rod moves at constant speed \(v\) perpendicular to the uniform field \(B\) . At time zero, the moving rod is next to the resistance \(R\). Equation Transcription: Text Transcription: 23.11 R A rho I v B

Problem 25CQ High-frequency noise in AC power can damage computers. Does the plug-in unit designed to prevent this damage use a large inductance or a large capacitance (in series with the computer) to filter out such high frequencies? Explain.

Integrated Concepts The Tethered Satellite in Figure \(23.12\) has a mass of \(525 kg\) and is at the end of a \(20.0 km\) long, \(2.50 mm\) diameter cable with the tensile strength of steel. (a) How much does the cable stretch if a \(100 N\) force is exerted to pull the satellite in? (Assume the satellite and shuttle are at the same altitude above the Earth.) (b) What is the effective force constant of the cable? (c) How much energy is stored in it when stretched by the \(100 N\) force? Equation Transcription: Text Transcription: 23.12 525 kg 20.0 km 2.50 mm 100 N

The \(12.0 cm\) long rod in Figure \(23.11\) moves at \(4.00 \mathrm{~m} / \mathrm{s}\). What is the strength of the magnetic field if a \(95.0 V\) emf is induced? Equation Transcription: Text Transcription: 12.0 cm 23.11 4.00 m/s 95.0 V

Problem 25PE Integrated Concept The Tethered Satellite discussed in this module is producing 5.00 kV, and a current of 10.0 A flows. (a) What magnetic drag force does this produce if the system is moving at 7.80 km/s? (b) How much kinetic energy is removed from the system in 1.00 h, neglecting any change in altitude or velocity during that time? (c) What is the change in velocity if the mass of the system is 100,000 kg? (d) Discuss the long term consequences (say, a week-long mission) on the space shuttle’s orbit, noting what effect a decrease in velocity has and assessing the magnitude of the effect.

Problem 26CQ Does inductance depend on current, frequency, or both? What about inductive reactance?

Explain why the capacitor in Figure \(23.55\)(a) acts as a low-frequency filter between the two circuits, whereas that in Figure \(23.55\)(b) acts as a high-frequency filter. Figure \(23.55\) Capacitors and inductors. Capacitor with high frequency and low frequency. Equation Transcription: Text Transcription: 23.55

If the capacitors in Figure \(23.55\) are replaced by inductors, which acts as a low-frequency filter and which as a high-frequency filter? Figure \(23.55\) Capacitors and inductors. Capacitor with high frequency and low frequency. Equation Transcription: Text Transcription: 23.55

Make a drawing similar to Figure \(23.14\), but with the pendulum moving in the opposite direction. Then use Faraday’s law, Lenz’s law, and \(RHR-1\) to show that magnetic force opposes motion. Equation Transcription: Text Transcription: 23.14 RHR-1

Figure \(23.59\) A coil is moved into and out of a region of uniform magnetic field. A coil is moved through a magnetic field as shown in Figure \(23.59\). The field is uniform inside the rectangle and zero outside. What is the direction of the induced current and what is the direction of the magnetic force on the coil at each position shown? Equation Transcription: Text Transcription: 23.59

Problem 28PE Calculate the peak voltage of a generator that rotates its 200-turn, 0.100 m diameter coil at 3600 rpm in a 0.800 T field.

Problem 29CQ Does the resonant frequency of an AC circuit depend on the peak voltage of the AC source? Explain why or why not.

Problem 29PE At what angular velocity in rpm will the peak voltage of a generator be 480 V, if its 500-turn, 8.00 cm diameter coil rotates in a 0.250 T field?

Problem 30CQ Suppose you have a motor with a power factor significantly less than 1. Explain why it would be better to improve the power factor as a method of improving the motor’s output, rather than to increase the voltage input.

Problem 30PE What is the peak emf generated by rotating a 1000-turn, 20.0 cm diameter coil in the Earth’s 5.00×10?5 T magnetic field, given the plane of the coil is originally perpendicular to the Earth’s field and is rotated to be parallel to the field in 10.0 ms?

Problem 32PE (a) A bicycle generator rotates at 1875 rad/s, producing an 18.0 V peak emf. It has a 1.00 by 3.00 cm rectangular coil in a 0.640 T field. How many turns are in the coil? (b) Is this number of turns of wire practical for a 1.00 by 3.00 cm coil?

Problem 33PE Integrated Concepts This problem refers to the bicycle generator considered in the previous problem. It is driven by a 1.60 cm diameter wheel that rolls on the outside rim of the bicycle tire. (a) What is the velocity of the bicycle if the generator’s angular velocity is 1875 rad/s? (b) What is the maximum emf of the generator when the bicycle moves at 10.0 m/s, noting that it was 18.0 V under the original conditions? (c) If the sophisticated generator can vary its own magnetic field, what field strength will it need at 5.00 m/s to produce a 9.00 V maximum emf?

Problem 36PE A 75-turn, 10.0 cm diameter coil rotates at an angular velocity of 8.00 rad/s in a 1.25 T field, starting with the plane of the coil parallel to the field. (a) What is the peak emf? (b) At what time is the peak emf first reached? (c) At what time is the emf first at its most negative? (d) What is the period of the AC voltage output?

Problem 35PE Show that if a coil rotates at an angular velocity ? , the period of its AC output is 2?/? .

Problem 34PE (a) A car generator turns at 400 rpm when the engine is idling. Its 300-turn, 5.00 by 8.00 cm rectangular coil rotates in an adjustable magnetic field so that it can produce sufficient voltage even at low rpms. What is the field strength needed to produce a 24.0 V peak emf? (b) Discuss how this required field strength compares to those available in permanent and electromagnets.

Problem 39PE Suppose a motor connected to a 120 V source draws 10.0 A when it first starts. (a) What is its resistance? (b) What current does it draw at its normal operating speed when it develops a 100 V back emf?

Problem 40PE A motor operating on 240 V electricity has a 180 V back emf at operating speed and draws a 12.0 A current. (a) What is its resistance? (b) What current does it draw when it is first started?

Problem 38PE Unreasonable Results A 500-turn coil with a 0.250 m2 area is spun in the Earth’s 5.00×10?5 T field, producing a 12.0 kV maximum emf. (a) At what angular velocity must the coil be spun? (b) What is unreasonable about this result? (c) Which assumption or premise is responsible?

Problem 41PE What is the back emf of a 120 V motor that draws 8.00 A at its normal speed and 20.0 A when first starting?

Problem 42PE The motor in a toy car operates on 6.00 V, developing a 4.50 V back emf at normal speed. If it draws 3.00 A at normal speed, what current does it draw when starting?

Problem 43PE Integrated Concepts The motor in a toy car is powered by four batteries in series, which produce a total emf of 6.00 V. The motor draws 3.00 A and develops a 4.50 V back emf at normal speed. Each battery has a 0.100 ? internal resistance. What is the resistance of the motor?

A plug-in transformer, like that in Figure \(23.29\), supplies \(9.00 V\) to a video game system. (a) How many turns are in its secondary coil, if its input voltage is \(120 V\) and the primary coil has \(400\) turns? (b) What is its input current when its output is \(1.30 A\)? Equation Transcription: Text Transcription: 23.29 9.00 V 120 V 400 1.30 A

Problem 46PE A cassette recorder uses a plug-in transformer to convert 120 V to 12.0 V, with a maximum current output of 200 mA. (a) What is the current input? (b) What is the power input? (c) Is this amount of power reasonable for a small appliance?

Problem 45PE An American traveler in New Zealand carries a transformer to convert New Zealand’s standard 240 V to 120 V so that she can use some small appliances on her trip. (a) What is the ratio of turns in the primary and secondary coils of her transformer? (b) What is the ratio of input to output current? (c) How could a New Zealander traveling in the United States use this same transformer to power her 240 V appliances from 120 V?

Problem 48PE (a) The plug-in transformer for a laptop computer puts out 7.50 V and can supply a maximum current of 2.00 A. What is the maximum input current if the input voltage is 240 V? Assume 100% efficiency. (b) If the actual efficiency is less than 100%, would the input current need to be greater or smaller? Explain.

Problem 47PE (a) What is the voltage output of a transformer used for rechargeable flashlight batteries, if its primary has 500 turns, its secondary 4 turns, and the input voltage is 120 V? (b) What input current is required to produce a 4.00 A output? (c) What is the power input?

Problem 50PE A large power plant generates electricity at 12.0 kV. Its old transformer once converted the voltage to 335 kV. The secondary of this transformer is being replaced so that its output can be 750 kV for more efficient cross-country transmission on upgraded transmission lines. (a) What is the ratio of turns in the new secondary compared with the old secondary? (b) What is the ratio of new current output to old output (at 335 kV) for the same power? (c) If the upgraded transmission lines have the same resistance, what is the ratio of new line power loss to old?

Problem 51PE If the power output in the previous problem is 1000 MW and line resistance is 2.00 ?, what were the old and new line losses?

Problem 53PE Construct Your Own Problem Consider a double transformer to be used to create very large voltages. The device consists of two stages. The first is a transformer that produces a much larger output voltage than its input. The output of the first transformer is used as input to a second transformer that further increases the voltage. Construct a problem in which you calculate the output voltage of the final stage based on the input voltage of the first stage and the number of turns or loops in both parts of both transformers (four coils in all). Also calculate the maximum output current of the final stage based on the input current. Discuss the possibility of power losses in the devices and the effect on the output current and power.

Problem 49PE A multipurpose transformer has a secondary coil with several points at which a voltage can be extracted, giving outputs of 5.60, 12.0, and 480 V. (a) The input voltage is 240 V to a primary coil of 280 turns. What are the numbers of turns in the parts of the secondary used to produce the output voltages? (b) If the maximum input current is 5.00 A, what are the maximum output currents (each used alone)?

Problem 55PE Two coils are placed close together in a physics lab to demonstrate Faraday’s law of induction. A current of 5.00 A in one is switched off in 1.00 ms, inducing a 9.00 V emf in the other. What is their mutual inductance?

Problem 52PE Unreasonable Results The 335 kV AC electricity from a power transmission line is fed into the primary coil of a transformer. The ratio of the number of turns in the secondary to the number in the primary is Ns / Np = 1000 . (a) What voltage is induced in the secondary? (b) What is unreasonable about this result? (c) Which assumption or premise is responsible?

Integrated Concepts A short circuit to the grounded metal case of an appliance occurs as shown in Figure \(23.60\). The person touching the case is wet and only has a \(3.00 \mathrm{k} \Omega\) resistance to earth/ground. (a) What is the voltage on the case if \(5.00 mA\) flows through the person? (b) What is the current in the short circuit if the resistance of the earth/ground wire is \(0.200 \Omega\) ? (c) Will this trigger the \(20.0 A\) circuit breaker supplying the appliance? Figure \(23.60\) A person can be shocked even when the case of an appliance is grounded. The large short circuit current produces a voltage on the case of the appliance, since the resistance of the earth/ground wire is not zero. Equation Transcription: Text Transcription: 23.60 3.00 K Omega 5.00 mA 0.200 Omega 20.0 A

Problem 56PE If two coils placed next to one another have a mutual inductance of 5.00 mH, what voltage is induced in one when the 2.00 A current in the other is switched off in 30.0 ms?

Problem 58PE A device is turned on and 3.00 A flows through it 0.100 ms later. What is the self-inductance of the device if an induced 150 V emf opposes this?

Problem 59PE Camera flashes charge a capacitor to high voltage by switching the current through an inductor on and off rapidly. In what time must the 0.100 A current through a 2.00 mH inductor be switched on or off to induce a 500 V emf?

Problem 57PE The 4.00 A current through a 7.50 mH inductor is switched off in 8.33 ms. What is the emf induced opposing this?

Problem 60PE Camera flashes charge a capacitor to high voltage by switching the current through an inductor on and off rapidly. In what time must the 0.100 A current through a 2.00 mH inductor be switched on or off to induce a 500 V emf?

Problem 62PE (a) Calculate the self-inductance of a 50.0 cm long, 10.0 cm diameter solenoid having 1000 loops. (b) How much energy is stored in this inductor when 20.0 A of current flows through it? (c) How fast can it be turned off if the induced emf cannot exceed 3.00 V?

Problem 63PE A precision laboratory resistor is made of a coil of wire 1.50 cm in diameter and 4.00 cm long, and it has 500 turns. (a) What is its self-inductance? (b) What average emf is induced if the 12.0 A current through it is turned on in 5.00 ms (one-fourth of a cycle for 50 Hz AC)? (c) What is its inductance if it is shortened to half its length and counterwound (two layers of 250 turns in opposite directions)?

Problem 64PE The heating coils in a hair dryer are 0.800 cm in diameter, have a combined length of 1.00 m, and a total of 400 turns. (a) What is their total self-inductance assuming they act like a single solenoid? (b) How much energy is stored in them when 6.00 A flows? (c) What average emf opposes shutting them off if this is done in 5.00 ms (one-fourth of a cycle for 50 Hz AC)?

Problem 65PE When the 20.0 A current through an inductor is turned off in 1.50 ms, an 800 V emf is induced, opposing the change. What is the value of the self-inductance?

Problem 66PE How fast can the 150 A current through a 0.250 H inductor be shut off if the induced emf cannot exceed 75.0 V?

Problem 67PE Integrated Concepts A very large, superconducting solenoid such as one used in MRI scans, stores 1.00 MJ of energy in its magnetic field when 100 A flows. (a) Find its self-inductance. (b) If the coils “go normal,” they gain resistance and start to dissipate thermal energy. What temperature increase is produced if all the stored energy goes into heating the 1000 kg magnet, given its average specific heat is 200 J/kg·ºC ?

Problem 68PE Unreasonable Results A 25.0 H inductor has 100 A of current turned off in 1.00 ms. (a) What voltage is induced to oppose this? (b) What is unreasonable about this result? (c) Which assumption or premise is responsible?

Problem 69PE If you want a characteristic RL time constant of 1.00 s, and you have a 500 ? resistor, what value of selfinductance is needed?

Problem 70PE Your RL circuit has a characteristic time constant of 20.0 ns, and a resistance of 5.00 M?. (a) What is the inductance of the circuit? (b) What resistance would give you a 1.00 ns time constant, perhaps needed for quick response in an oscilloscope?

Problem 71PE A large superconducting magnet, used for magnetic resonance imaging, has a 50.0 H inductance. If you want current through it to be adjustable with a 1.00 s characteristic time constant, what is the minimum resistance of system?

Problem 72PE Verify that after a time of 10.0 ms, the current for the situation considered in Example 23.9 will be 0.183 A as stated. Example 23.9 Calculating Characteristic Time and Current in an RL Circuit: (a) What is the characteristic time constant for a 7.50 mH inductor in series with a 3.00 ? resistor? (b) Find the current 5.00 ms after the switch is moved to position 2 to disconnect the battery, if it is initially 10.0 A.

Problem 73PE Suppose you have a supply of inductors ranging from 1.00 nH to 10.0 H, and resistors ranging from 0.100 ? to 1.00 M?. What is the range of characteristic RL time constants you can produce by connecting a single resistor to a single inductor?

Problem 74PE (a) What is the characteristic time constant of a 25.0 mH inductor that has a resistance of 4.00 ?? (b) If it is connected to a 12.0 V battery, what is the current after 12.5 ms?

Problem 75PE What percentage of the final current I0 flows through an inductor L in series with a resistor R , three time constants after the circuit is completed?

Problem 77PE (a) Use the exact exponential treatment to find how much time is required to bring the current through an 80.0 mH inductor in series with a 15.0 ? resistor to 99.0% of its final value, starting from zero. (b) Compare your answer to the approximate treatment using integral numbers of ? . (c) Discuss how significant the difference is.

Problem 81PE What capacitance should be used to produce a 2.00 M? reactance at 60.0 Hz?

The \(5.00 A\) current through a \(1.50 H\) inductor is dissipated by a \(2.00 \Omega\) resistor in a circuit like that in Figure \(23.44\) with the switch in position \(2\). (a) What is the initial energy in the inductor? (b) How long will it take the current to decline to \(5.00 \%\) of its initial value? (c) Calculate the average power dissipated, and compare it with the initial power dissipated by the resistor. Equation Transcription: Text Transcription: 5.00 A 1.50 H 2.00 Omega 23.44 2 5.00%

Problem 78PE (a) Using the exact exponential treatment, find the time required for the current through a 2.00 H inductor in series with a 0.500 ? resistor to be reduced to 0.100% of its original value. (b) Compare your answer to the approximate treatment using integral numbers of ? . (c) Discuss how significant the difference is.

Problem 80PE What value of inductance should be used if a 20.0 k? reactance is needed at a frequency of 500 Hz?

Problem 79PE At what frequency will a 30.0 mH inductor have a reactance of 100 ??

Problem 82PE At what frequency will an 80.0 mF capacitor have a reactance of 0.250 ??

Problem 83PE (a) Find the current through a 0.500 H inductor connected to a 60.0 Hz, 480 V AC source. (b) What would the current be at 100 kHz?

Problem 84PE (a) What current flows when a 60.0 Hz, 480 V AC source is connected to a 0.250 ?F capacitor? (b) What would the current be at 25.0 kHz?

Problem 85PE A 20.0 kHz, 16.0 V source connected to an inductor produces a 2.00 A current. What is the inductance?

Problem 87PE (a) An inductor designed to filter high-frequency noise from power supplied to a personal computer is placed in series with the computer. What minimum inductance should it have to produce a 2.00 k? reactance for 15.0 kHz noise? (b) What is its reactance at 60.0 Hz?

Problem 86PE A 20.0 Hz, 16.0 V source produces a 2.00 mA current when connected to a capacitor. What is the capacitance?

The capacitor in Figure \(23.55\)(a) is designed to filter low-frequency signals, impeding their transmission between circuits. (a) What capacitance is needed to produce a \(100 \mathrm{k} \Omega\) reactance at a frequency of \(120 Hz\)? (b) What would its reactance be at \(1.00 MHz\)? (c) Discuss the implications of your answers to (a) and (b). Equation Transcription: Text Transcription: 23.55 100 k Omega 120 Hz 1.00 MHz

Problem 90PE Unreasonable Results In a recording of voltages due to brain activity (an EEG), a 10.0 mV signal with a 0.500 Hz frequency is applied to a capacitor, producing a current of 100 mA. Resistance is negligible. (a) What is the capacitance? (b) What is unreasonable about this result? (c) Which assumption or premise is responsible?

The capacitor in Figure \(23.55\)(b) will filter high-frequency signals by shorting them to earth/ground. (a) What capacitance is needed to produce a reactance of \(10.0 \mathrm{~m} \Omega\) for a \(5.00 kHz\) signal? (b) What would its reactance be at \(3.00 Hz\)? (c) Discuss the implications of your answers to (a) and (b). Equation Transcription: Text Transcription: 23.55 10.0 m Omega 5.00 kHz 3.00 Hz

Problem 91PE Construct Your Own Problem Consider the use of an inductor in series with a computer operating on 60 Hz electricity. Construct a problem in which you calculate the relative reduction in voltage of incoming high frequency noise compared to 60 Hz voltage. Among the things to consider are the acceptable series reactance of the inductor for 60 Hz power and the likely frequencies of noise coming through the power lines.

Problem 92PE An RL circuit consists of a 40.0 ? resistor and a 3.00 mH inductor. (a) Find its impedance Z at 60.0 Hz and 10.0 kHz. (b) Compare these values of Z with those found in Example 23.12 in which there was also a capacitor. Example 23.12: Calculating Impedance and Current An RLC series circuit has a 40.0 ? resistor, a 3.00 mH inductor, and a 5.00 ?F capacitor. (a) Find the circuit’s impedance at 60.0 Hz and 10.0 kHz, noting that these frequencies and the values for L and C are the same as in Example 23.10 and Example 23.11. (b) If the voltage source has Vrms = 120 V , what is Irms at each frequency?

Problem 93PE An RC circuit consists of a 40.0 ? resistor and a 5.00 ?F capacitor. (a) Find its impedance at 60.0 Hz and 10.0 kHz. (b) Compare these values of Z with those found in Example 23.12, in which there was also an inductor. Example 23.12: Calculating Impedance and Current An RLC series circuit has a 40.0 ? resistor, a 3.00 mH inductor, and a 5.00 ?F capacitor. (a) Find the circuit’s impedance at 60.0 Hz and 10.0 kHz, noting that these frequencies and the values for L and C are the same as in Example 23.10 and Example 23.11. (b) If the voltage source has Vrms = 120 V , what is Irms at each frequency?

Problem 95PE What is the resonant frequency of a 0.500 mH inductor connected to a 40.0 ?F capacitor?

Problem 96PE To receive AM radio, you want an RLC circuit that can be made to resonate at any frequency between 500 and 1650 kHz. This is accomplished with a fixed 1.00 ?H inductor connected to a variable capacitor. What range of capacitance is needed?

Problem 97PE Suppose you have a supply of inductors ranging from 1.00 nH to 10.0 H, and capacitors ranging from 1.00 pF to 0.100 F. What is the range of resonant frequencies that can be achieved from combinations of a single inductor and a single capacitor?

Problem 94PE An LC circuit consists of a 3.00 mH inductor and a 5.00 µF capacitor. (a) Find its impedance at 60.0 Hz and 10.0 kHz. (b) Compare these values of Z with those found in Example 23.12 in which there was also a resistor. Example 23.12: Calculating Impedance and Current An RLC series circuit has a 40.0 ? resistor, a 3.00 mH inductor, and a 5.00 ?F capacitor. (a) Find the circuit’s impedance at 60.0 Hz and 10.0 kHz, noting that these frequencies and the values for L and C are the same as in Example 23.10 and Example 23.11. (b) If the voltage source has Vrms = 120 V , what is Irms at each frequency?

Problem 98PE What capacitance do you need to produce a resonant frequency of 1.00 GHz, when using an 8.00 nH inductor?

Problem 99PE What inductance do you need to produce a resonant frequency of 60.0 Hz, when using a 2.00 ?F capacitor?

Problem 100PE The lowest frequency in the FM radio band is 88.0 MHz. (a) What inductance is needed to produce this resonant frequency if it is connected to a 2.50 pF capacitor? (b) The capacitor is variable, to allow the resonant frequency to be adjusted to as high as 108 MHz. What must the capacitance be at this frequency?

Problem 102PE An RLC series circuit has a 1.00 k? resistor, a 150 ?H inductor, and a 25.0 nF capacitor. (a) Find the circuit’s impedance at 500 Hz. (b) Find the circuit’s impedance at 7.50 kHz. (c) If the voltage source has Vrms = 408 V , what is Irms at each frequency? (d) What is the resonant frequency of the circuit? (e) What is Irms at resonance?

Problem 101PE An RLC series circuit has a 2.50 ? resistor, a 100 ?H inductor, and an 80.0 ?F capacitor.(a) Find the circuit’s impedance at 120 Hz. (b) Find the circuit’s impedance at 5.00 kHz. (c) If the voltage source has Vrms = 5.60 V , what is Irms at each frequency? (d) What is the resonant frequency of the circuit? (e) What is Irms at resonance?

Problem 105PE An RLC series circuit has a 200 ? resistor and a 25.0 mH inductor. At 8000 Hz, the phase angle is 45.0º . (a) What is the impedance? (b) Find the circuit’s capacitance. (c) If Vrms = 408 V is applied, what is the average power supplied?

Problem 61PE A large research solenoid has a self-inductance of 25.0 H. (a) What induced emf opposes shutting it off when 100 A of current through it is switched off in 80.0 ms? (b) How much energy is stored in the inductor at full current? (c) At what rate in watts must energy be dissipated to switch the current off in 80.0 ms? (d) In view of the answer to the last part, is it surprising that shutting it down this quickly is difficult?

Problem 2CQ When a magnet is thrust into a coil as in Figure 23.4(a), what is the direction of the force exerted by the coil on the magnet? Draw a diagram showing the direction of the current induced in the coil and the magnetic field it produces, to justify your response. How does the magnitude of the force depend on the resistance of the galvanometer?

Referring to Figure 23.58, what are the directions of the currents in coils \(1\), \(2\), and \(3\) (assume that the coils are lying in the plane of the circuit): (a) When the switch is first closed? (b) When the switch has been closed for a long time? (c) Just after the switch is opened? Figure 23.58 Equation Transcription: Text Transcription: 1 2 3

Problem 37PE (a) If the emf of a coil rotating in a magnetic field is zero at t = 0 , and increases to its first peak at t = 0.100 ms , what is the angular velocity of the coil? (b) At what time will its next maximum occur? (c) What is the period of the output? (d) When is the output first one-fourth of its maximum? (e) When is it next one-fourth of its maximum?